background image

22

   

|

   

KDC-4547U/ KDC-4047U/ KDC-4047UGY/ KDC-4047UM/ KDC-414UM/ KDC-414U

Troubleshooting Guide

Some functions of this unit may be disabled by 
some settings made on this unit. 

 ! 

  •  Cannot set up the subwoofer.

 

•  Cannot set up the low pass filter.

 

•  No output from the subwoofer.

 •  <Subwoofer output> of <Function Setting> (page 

8) is not set to On. 

 

•  Preout is not set to subwoofer. 

 “SWITCH  PRE”/ 

“SWITCH PREOUT” of <Function Setting> (page 8) 

 ! 

    Cannot set up the subwoofer Phase.

   Subwoofer Low Pass Filter is set to “THROUGH”. 

 “LPF SUB-W”/ “LPF SUBWOOFER” of <Function 

Setting> (page 8) 

 ! 

     Power OFF Timer does not function.

 <Exit of the Demonstration Mode> (page 4) is not 

turned off. 

 ! 

  The number of songs contained in "SONGS" 

category of this unit is different from that 
contained in "SONGS" category of iPod.

  Podcast files are not counted in this unit as this unit 

does not support the playback of podcast files.

 ! 

  Volume cannot be adjusted.

 •  The unit is set to Music Search mode. 

 Cancel the 

Music Search mode. (page 12) 

 

•  The unit is set to Function Setting mode. 

 Cancel 

the Function Setting mode. (page 8) 

What might seem to be a malfunction in your unit 
may just be the result of slight misoperation or 
miswiring. Before calling service, first check the 
following table for possible problems.

General

 ? 

  The Touch Sensor Tone (beep sound) does not 

sound.

  The preout jack is being used.

  The Touch Sensor Tone cannot be output from 

the preout jack.

Tuner source

 ? 

  Radio reception is poor.

  The car antenna is not extended.

  Pull the antenna out all the way.

Disc source

 ? 

  The specified disc does not play, but another one 

plays instead.

  The specified CD is quite dirty.

  Clean the CD, referring to the CD cleaning of the 

section on <Handling CDs> (page 3).

  The disc is severely scratched.

  Try another disc instead.

Audio file source

 ? 

  The sound skips when an Audio file is being 

played.

  The media is scratched or dirty.

☞ 

Clean the media, referring to the CD cleaning of 
the section on <Handling CDs> (page 3).

  The recording condition is bad.

  Record the media again or use another media.

B64-4526-00_00_en.indd   22

09.10.2   2:29:55 PM

Summary of Contents for KDC-4047U

























Reviews: