Kenwood KAC-816 Instruction Manual Download Page 6

• The genuine-accessory car stereo shall have a maximum power output of no more than 25 W.
• Do not connect the speaker output leads from a power amplifier (Optional) to the speaker input

terminals of this unit, for this may cause malfunction  or damage. 

• Do not connect cables and leads to both RCA cable input jacks and the speaker input terminals

simultaneously, for this may cause malfunction or damage.

• Connect the power control lead to a power supply which can be turned ON/OFF by the ignition

key switch (ACC line). 
With this connection, shock noise may be generated when the power of the genuine-accessory
car stereo is switched ON/OFF.

2

CAUTION

6

Connection 

MONO

POWER AMPLIFIER

L

25Hz

15Hz

INFRASONIC

OFF

INPUT

SENSITIVITY(V)

LPF

FREQUENCY(Hz)

GND

R

LINE IN

0.3

0.5

1

2

3

4

5

0.2

150

100

70

50

200

LEFT

RIGHT

SPEAKER LEVEL INPUT

-

+

MONO

POWER AMPLIFIER

L

25Hz

15Hz

INFRASONIC

OFF

INPUT

SENSITIVITY(V)

LPF

FREQUENCY(Hz)

GND

R

LINE IN

0.3

0.5

1

2

3

4

5

0.2

150

100

70

50

200

LEFT

RIGHT

SPEAKER LEVEL INPUT

RCA cable connection

CENTER UNIT

(Cassette receiver, 

CD receiver, etc.)

Power control cable
(Commercially
available part)

RCA cable
(Commercially
available part)

Do not connect cables and
leads to both RCA cable input
jacks and the speaker input
terminals simultaneously,  for
this may cause malfunction
or damage.

2

CAUTION

RCA cable ground terminal

When using an RCA cable with
a ground lead attached, connect
the ground lead to this terminal.

Do not use this terminal for power source
grounding. This unit will be damaged if the
power source grounding wire is connected
to this terminal.

2

CAUTION

Genuine-accessory

car stereo

Speaker level input connection

ACC

Battey

Left output (White)

Right output (Red)

Left input

Right input

Left input

Right input

Left output 

Right output 

Lead terminal
(Commercially
available parts)

Speaker level input terminals

Summary of Contents for KAC-816










Reviews: