Kenwood KAC-8104D - Amplifier Instruction Manual Download Page 4

4  

English

2

WARNING

To prevent fire caused by a short in the wiring, 
connect a fusible link or breaker nearby the 
battery’s positive terminal.

2

CAUTION

•  If sound is not output normally, immediately turn 

power off and check connections.

•  Be sure to turn the power off before changing the 

setting of any switch.

•  If the fuse blows, check wires for shorts, then 

replace the fuse with one of the same rating.

•  Check that no unconnected wires or connectors 

are touching the car body. Do not remove 
caps from unconnected wires or connectors to 
prevent short circuits.

•  Connect the speaker wires to appropriate speaker 

connectors separately. Sharing the negative wire 
of the speaker or grounding speaker wires to the 
metal body of the car can cause this unit to fail.

NOTE

•  Do not connect cables and leads to both RCA 

cable input jacks and the speaker level input 
terminals simultaneously, for this may cause 
malfunction or damage.

Speaker level input connections

•  The genuine-accessory car stereo shall have a 

maximum power output of no more than 40 W.

•  The power is turned on and off as the unit 

detects input signal (Signal Sensing Turn-ON). 
There fore it is not necessary to connect the 
power control wire.

Speaker output terminals

•  As this unit accepts speakers with a minimum 

impedance of 2 ohms, connect speakers with 2-
ohms or higher impedance to these terminals.

LINE OUT terminal

•  The signal that’s input from the line input 

terminal is output. 

Fuse 

40 A × 1

40

Connection 

Lead terminal*

Battery

Ground wire*

Power control wire* 
(RCA cable connection)

Subwoofer (L + R) 
(≥2Ω)

Battery wire*

Protective Fuse*

Terminal cover 

40

CENTER UNIT
(CD receiver, etc.)

RCA cable*

Power control wire 

Left input

Right input

40

 RCA cable or Speaker level input connection

 Power wire and Speaker wire connection

Genuine-accessory car 
stereo (No line output 
center unit etc.) 

• RCA cable connections

• Speaker level input connections

Cable Color of the connector

 Left

9

 White

·

 White/Black

 Right

9

 Gray

·

 Gray/Black

* Commercially available parts

(4Ω + 4Ω)

When two subwoofers are 
connected. (≥4Ω)

LINE OUT terminal

(2Ω + 2Ω)

• Dual voice coil subwoofer

B64-3931-00̲00̲KE.indb   4

B64-3931-00̲00̲KE.indb   4

07.10.24   11:40:01 AM

07.10.24   11:40:01 AM

Summary of Contents for KAC-8104D - Amplifier

















Reviews: