background image

3

Protection function

This unit is equipped with a protection function for protecting this unit and your speakers
from various accidents or problems that can occur.
When the protection function is triggered, the Power indicator goes off and the amplifier
stops operating.

Power indicator:

When the power is turned on, the Power indicator lights.
If the Power indicator does not light when the power is turned on, the
protection function may be activated. Check whether there is any
indication of trouble.

The protection function activates in the following
situations:

• When a speaker cable may be short-circuited.
• When a speaker output contacts ground.
• When the unit malfunctions and a DC signal is sent to the speaker

output.

• When the temperature of internal parts exceeds 120°C (248°F).
• When a ground cable of the center unit (cassette receiver, CD receiver,

etc.) or this unit is not connected to a metal part serving as an
electrical ground passing electricity to the battery's negative 

-

terminal.

Power indicator

Installation procedure

1. Remove the ignition key and disconnect the negative 

-

terminal of the battery to prevent short

circuits. 

2. Set the unit according to the intended usage.
3. Connect the input and output cables of the units.
4. Connect the speaker cables.
5. Connect the power cable, power control cable and grounding cable following this order.
6. Install the unit in the car.
7. Connect the negative 

-

terminal of the battery.

• Be sure to turn the power off before changing the setting of any switch.
• If the fuse blows, check cables for shorts, then replace the fuse with one of the same rating.
• Check that no unconnected cables or connectors are touching the car body. Do not remove

caps from unconnected cables or connectors to prevent short circuits.

• Connect the speaker cables to appropriate speaker connectors separately. Sharing the negative

cable of the speaker or grounding speaker cables to the metal body of the car can cause this
unit to fail.

• After installation, check that the brake lamps, winkers, and wipers work properly.

2

CAUTION

Summary of Contents for KAC-628













Reviews: