2
liquidiser
filler cap
lid
jug
sealing ring
blade unit
additional attachments
Not all of these attachments listed below will be included with your food
processor. Please refer to your content list supplied. To buy an attachment not
included in your pack, contact the dealer from whom you purchased your
appliance.
knife blade
dough tool
twin beater geared whisk
maxi-blend canopy
thick slicing/coarse shredding disc
thin slicing/fine shredding disc
fine (Julienne style) chipper disc
extra coarse shredding disc (UK - not available)
rasping disc
standard chipper disc (UK - not available)
geared citrus press
spatula
disc storage box
multi mill
centrifugal juicer
recipe book
to use your food processor
1 Fit the detachable shaft onto the power unit
.
2 Then fit the bowl. Place the handle towards the back and turn clockwise until it
locks
.
3 Fit an attachment over the drive shaft.
●
Always fit the bowl and attachment onto the machine before adding ingredients.
4 Fit the lid
- ensuring the top of the drive shaft locates into the centre of the lid.
●
Do not use the lid to operate the processor, always use the on/off
speed control.
5 Switch on and select a speed.
●
The processor won’t work if the bowl and lid are fitted
incorrectly.
●
Use the pulse control for short bursts. The pulse will operate for as long as the
lever is held down.
6 Reverse the above procedure to remove the lid, attachments and bowl.
●
Always switch off before removing the lid.
important
●
Your processor is not suitable for crushing or grinding coffee beans, or
converting granulated sugar to caster sugar.
●
When adding almond essence or flavouring to mixtures avoid contact with the
plastic as this may result in permanent marking.
to use your liquidiser
1 Fit the sealing ring
into the blade unit
.
2 Screw the jug onto the blade unit.
3 Put your ingredients into the jug.
4 Put the filler cap in the lid, then turn.
5 Lock the lid onto the jug so that the thumb tab is over the handle (To unlock the
lid, push the thumb tab
.)
6 Place the liquidiser onto the power unit and turn to lock
.
7 Select a speed or use the pulse control.
21
22
23
24
25
26
27
28
29
30
31
a
safety
●
The blades and discs are very sharp, handle with care.
Always hold the knife blade by the finger grip
at the top, away from the cutting edge, both
when handling and cleaning.
●
Always remove the knife blade before pouring contents from the bowl.
●
Keep hands and utensils out of the processor bowl and liquidiser jug whilst
connected to the power supply.
●
Switch off and unplug:
●
●
before fitting or removing parts
●
●
after use
●
●
before cleaning
●
Never use your fingers to push food down the feed tube. Always use the
pusher/s supplied.
●
Before removing the lid from the bowl or liquidiser/mill from the power unit:-
●
●
switch off;
●
●
wait until the attachment/blades have completely stopped;
●
●
Be careful not to unscrew the liquidiser jug or mill from the blade unit.
●
Allow hot liquids to cool before blending in the liquidiser - if you haven’t fitted
the lid securely and it comes off, you could get splashed.
●
Do not use the lid to operate the processor, always use the on/off speed control.
●
This machine will be damaged and may cause injury if the
interlock mechanism is subjected to excessive force.
●
This machine is not intended for use by young children or infirm persons without
supervision.
●
Never use an unauthorised attachment.
●
Don’t let children play with this machine.
●
Never leave the machine on unattended.
●
Never use a damaged machine. Get it checked or repaired: see ‘service’.
●
Never let the power unit, cord or plug get wet.
●
Don’t let excess cord hang over the edge of a table or worktop or touch hot
surfaces.
●
Never misuse your food processor and only use it for its intended domestic use.
before plugging in
●
Make sure your electricity supply is the same as the one shown on the
underside of your machine.
important- UK only
●
The wires in the cord are coloured as follows:
Blue = Neutral
Brown = Live
●
This appliance complies with European Economic Community Directive
89/336/EEC.
before using for the first time
1 Remove all packaging including the plastic blade covers from the knife blade.
Take care the blades are very sharp.
These covers should be discarded
as they are to protect the blade during manufacture and transit only.
2 Wash the parts see ‘cleaning’
3 Push excess cord into the back of the machine.
key
processor
power unit
detachable drive shaft
bowl
lid
feed tube
pushers
safety interlock
cord storage
pulse control
speed control
a
