Kenwood DNX649VBT, Instruction Manual

Page: 38 / 45

74 74 75
Return to the Top page
Troubleshooting
Return to the Top page
Troubleshooting
Problems And Solutions
If any trouble occurs, first check the following table for possible problems.
• Some functions of this unit may be disabled by some settings made on this unit.
• What might seem to be a malfunction in your unit may just be the result of slight misoperation
or miswiring.
About settings
Problem Reason Solution
• Cannot set up the subwoofer.
• Cannot set up subwoofer phase.
• No output from the subwoofer.
• Cannot set up the low pass filter.
• Cannot set up the high pass filter.
Subwoofer is not set
to on.
Set the subwoofer to on.
See Speaker setup (P.64) .
The dual zone function
is enabled.
Set the dual zone function to off.
See Zone Control (P.68) .
• Cannot select the output
destination of the subsource in
the dual zone.
• Cannot adjust the volume of the
rear speakers.
The dual zone function
is disabled.
Set the dual zone function to on.
See Zone Control (P.68) .
• Cannot set up the equalizer.
• Cannot set up the crossover
network.
The dual zone function
is enabled.
Set the dual zone function to off.
See Zone Control (P.68) .
About audio operations
Problem Reason Solution
Radio reception is poor. The car antenna is not
extended.
Pull out the antenna all the way.
The antenna control
wire is not connected.
Connect the wire correctly.
See “Connection” in the Quick Start Guide.
Cannot play audio files stored in
a disc.
“CD Read” is set to “2”. Set “CD Read” to “1”.
See Disc setup (P.25) .
Cannot select a folder. The random play
function is enabled.
Turn off the random function.
Cannot perform repeat play
during VCD playback.
The PBC function is
enabled.
Turn off the PBC function.
The specified disc does not play,
but another one plays instead.
The disc is quite dirty. Clean the disc.
See Precautions on handling discs (P.4) .
The disc is severely
scratched.
Try another disc instead.
The sound skips when an audio
file is being played.
The disc is scratched
or dirty.
Clean the disc.
See Precautions on handling discs
(P.4) .
The recording
condition is bad.
Record the file again or use another disc.
T
roubleshooting
Other
Problem Reason Solution
The Touch Sensor Tone doesn’t
sound.
The preout jack is being
used.
The Touch Sensor Tone cannot be output
from the preout jack.
Error Messages
When you fail to operate the unit correctly, the cause of the failure appears as the message on
the screen.
Error Message Cause Solution
Protect Protective circuit has been activated
because a speaker cord has shorted
or it has come in contact with the
car chassis.
Wire or insulate the speaker cord as
appropriate and then push the <Reset>
button (P.77) .
Hot Error When the internal temperature of
this unit rises to 60°C or more, the
protection circuit is activated and
you may not be able to operate
the unit.
Use the unit again after reducing the
temperature of the unit.
Mecha Error The disc player is malfunctioning. Eject the disc and try inserting it again. Contact
the Kenwood dealer if this indicator continues
blinking or the disc cannot be ejected.
Disc Error An unplayable disc is inserted. Change the disc.
See Playable Media And Files (P.78) .
Read Error The disc is quite dirty. Clean the disc.
See Precautions on handling discs (P.4) .
Disc is upside down. Load the disc with the labeled side up.
Region Code
Error
The disc you wanted to play has a
region code that cannot be played
with this unit.
See Region Codes In The World (P.83) or try
another disc.
Parental Level
Error
The disc you wanted to play has a
higher level than the parental level
you set.
Set the parental level.
See Parental level (P.24) .
Error 07–67 The unit is not operating correctly
due to some reason or other.
Push the unit’s Reset button. If the “Error
07−67” message does not disappear, see your
nearest Kenwood dealer.
No Device (USB
device)
The USB device is selected as a
source although no USB device is
connected.
Change the source to any source other than
USB/iPod. Connect a USB device, and change
the source to USB again.
Disconnected
(iPod)
The iPod is selected as a source
although no iPod is connected.
Change the source to any source other than
iPod. Connect an iPod, and change the source
to iPod again.
No Media file The connected USB device contains
no playable audio file. Media was
played that doesn’t have data
recorded that the unit can play.
See Playable Media And Files (P.78) and try
another USB device.