Kenwood CT-203 Instruction Manual Download Page 26

Page: 26 / 28

CT-2050/203/KXF-W6010/W4010 (En/M)

In case of difficulty

Use a cassette with unbroken tab or close the
hole.

Close the cassette holder completely.

Adjust the recording level referring to

"How

to record"

Press the input selector key of the source

to be recorded.

Change the tape transport direction of deck
or insert the tape inversely.

Demagnetize the head referring to

"Clean-

ing the head section"

Install the system apart from other electrical
appliances and TV set.

Change the arrangement or the position of the
equipment.

Adjust the recording level referring to

"How

to record"

Set the

DOLBY NR

key to B or C.

Clean the capstans and pinch rollers.

Wind the tape regularly by fast forwarding,
rewinding or playing it fully from one reel to
another.

Set the

TIMER

switch to OFF unless timer

playback or timer recording is required.

The protection tab on the cassette has been
broken.

The cassette holder is not closed completely.

The recording level is set to the minimum
position.

The TAPE input selector is selected on the
amplifier.

Tape has been fully wound to a reel.

The head is magnetized.

External noise is induced.

The system assembly position is wrong.

The recording level was too low.

A tape recorded with Dolby NR ON is being
played with Dolby NR OFF.

The capstans or pinch rollers are dirty.

Tape is irregularly wound.

The

TIMER

switch is set to PLAY or REC.

Symptom

Remedy

Cause

Recording is not initiated when the REC/
ARM (

) key is pressed.

Noise level is high.

Sound is vibrating.

Playback or recording starts immediately
when the power is switched ON.

With some tapes, a squeaky noise is produced when the tape is stopped automatically. This is due to the tape protection function, and not
a malfunction.

Note

Summary of Contents for CT-203





























Search results

Summary of Contents for CT-203

Reviews:

Brands by name

Popular brands

Kenwood CT-203, Instruction Manual

Search results

Summary of Contents for CT-203

Reviews:

Brands by name

Popular brands