manualshive.com logo in svg

Kenwood Basic M1, Quick Start Manual

The Kenwood Basic M1, an exceptional audio amplifier, offers stunning sound quality and advanced features. To get started quickly, a comprehensive Quick Start Manual is provided for download, completely free, at manualshive.com. Enhance your audio experience with this sleek and powerful amplifier.

Share
Download
background image

Kenwood BASIC M1 Current Source Modification 

www.drmaudtioht.com

 

10/9/2008 6:56 PM 

page 7 of 10 

This photo shows the top side of the amplifier pc board assembly with the original current source resistor 
R18 removed: 

 

   

 

 
 

This photo shows the bottom side of the amplifier pc board assembly with the original current source 
resistor R17 removed:  
 

 

Summary of Contents for Basic M1











Reviews:

No comments

Related manuals for Basic M1

Lab.gruppen FP14000 User Manual preview
FP14000
Brand: Lab.gruppen Pages: 5
Lab.gruppen FP14000 Technical Data preview
FP14000
Brand: Lab.gruppen Pages: 2
Lab.gruppen fP Series FP 2400Q User Manual preview
fP Series FP 2400Q
Brand: Lab.gruppen Pages: 20
Lab.gruppen PLM Series PLM 10000Q User Manual Addendum preview
PLM Series PLM 10000Q
Brand: Lab.gruppen Pages: 25
Lab.gruppen fP Series FP 2200 Specifications preview
fP Series FP 2200
Brand: Lab.gruppen Pages: 2
Lab 12 MIGHTY Owner'S Manual preview
MIGHTY
Brand: Lab 12 Pages: 8
NAD 314 Service Manual preview
314
Brand: NAD Pages: 18
Lab.gruppen LAB 2002 Specifications preview
LAB 2002
Brand: Lab.gruppen Pages: 2
Laney LC15 User Manual preview
LC15
Brand: Laney Pages: 8
Lab.gruppen C 88:4 Operation Manual preview
C 88:4
Brand: Lab.gruppen Pages: 44
NAD PP 375 Mounting Instruction preview
PP 375
Brand: NAD Pages: 2
NAD Masters M3 Specification Sheet preview
Masters M3
Brand: NAD Pages: 4
Nady Audio XA Owner'S Manual preview
XA
Brand: Nady Audio Pages: 12
NAD C375BEE Datasheet preview
C375BEE
Brand: NAD Pages: 4
NAD M10 V2 Quick Start Manual preview
M10 V2
Brand: NAD Pages: 2
NAD M10 V2 Owner'S Manual preview
M10 V2
Brand: NAD Pages: 16
NAD CI 8-120 DSP Quick Setup Manual preview
CI 8-120 DSP
Brand: NAD Pages: 2
Jobsite AB50-X2 Datasheet preview
AB50-X2
Brand: Jobsite Pages: 4

Brands by name

Popular brands

Load more brands