Kenton KILLAMIX-MINI User Manual Download Page 6

 

6

On – two modes are available indicated by the LEDs lit on the ledring above button 2 
1 – four pole mode with centre zero (CCs 19,20,21,22) sending analogue values 0 –127 
2 – four pole mode switching joystick (CCs 19,20,21,22) only value 127 sent at limits 
When in 4 pole mode, the centre position is zero, and moving right sends CC#19, up sends 
CC#20, left sends CC#21 and down sends CC#22. 
 

Button 3

 – Receive CCs for Encoders and Push buttons 

Off = incoming MIDI messages ignored (default) 
On = two modes are available indicated by the LEDs lit on the ledring above button 3 
 
1) Allow received CCs to update Encoder and Push button values for all channels.  
 
    This mode updates ALL CCs on ALL channels – even if that channel is not the one currently  
    selected, however  note the following exception: 
    For push buttons, only buttons set to toggle mode will be updated because this is the only  
    mode that can be meaningfully used. Push buttons set to on-only or on-off modes will still  
   operate as usual but will not be updated by received CCs. 
 
2) Allow received CCs to update Encoders 
    Allow received CCs (or Notes if selected) to update push button LEDs *ONLY*  
    Push button LEDs are not directly updated from the buttons.  
    Works for all 3 button modes – on only / on-off / toggle 
 

Button 4

 – Hi-Speed Encoder mode 

Off = normal 3 speed operation (default) 
On = hi-speed mode active  
Hi-Speed mode is implemented so that turning the encoder VERY slowly will still increment or 
decrement slowly, but anything faster will operate at hi-speed. 
 

Button 5

 – Buttons send MIDI notes  

Off = buttons send controllers (CCs 10 - 18) as standard – (default)  
On = push buttons send MIDI notes instead of controllers 
There are 4 active modes which are indicated by the LED-ring above button 5. Where the 
following LEDs are lit, modes are as follows: 
1) Impulse mode for Ableton drums - buttons are mapped to white keys only from middle C 
(MIDI note #60) 
2) Consecutive mode (white & black keys) starting from MIDI note #36 
3) Consecutive mode (white & black keys) starting from MIDI note #48 
4) Consecutive mode (white & black keys) starting from MIDI note #60 
 
Remember to set the individual buttons to their on/off mode if you want to send note-offs when 
you release the buttons. 
 

Button 6

 – Knobs pressed send controller messages mode (instead of changing channel) 

Off = Knobs pressed change MIDI channel (default) 
On = The selected modes are indicated by the LED-ring above button 6.  
The LED ring above button 6 indicates the mode: 
1) Knobs send controllers 24-32 with value 127 when pressed (nothing when released) 
2) Knobs send controllers 24-32 with value 127 when pressed and with value 0 when released 
 

Summary of Contents for KILLAMIX-MINI













Reviews: