Kentix AlarmManager-BASIC User Manual Download Page 35

Page: 35 / 129

6.7. MultiSensor-Door

The MultiSensor-Door is designed for an efficient intrusion detection on doors or windows or for a specific
environmental monitoring in a server rack.

The MultiSensor-Door is configured via the ControlCenter.

Updating the device is not necessary / possible.

Interior view - MultiSensor-Door

Page

(07-2018, subject to change)

kentix.com

LED red / green (Top of sensor case)

Normal running mode:
LED red

- blinking 1x on alarm

LED green

- OFF

Teach-IN process:
LED green

blinking: Teach-IN process started

- ON: Teach-IN completed

LED red

- OFF

Reed- / Magnetic contact (next to battery)

Learn button

lti

ito

Summary of Contents for AlarmManager-BASIC


































































































































Search results

Summary of Contents for AlarmManager-BASIC

Reviews:

Related manuals for AlarmManager-BASIC

Brands by name

Popular brands

Kentix AlarmManager-BASIC, User Manual

Search results

Summary of Contents for AlarmManager-BASIC

Reviews:

Related manuals for AlarmManager-BASIC

Brands by name

Popular brands