background image

Loading

Property loading your dryer can lower your utility bill and prolong

the life of your gannents.

Loading suggestions

Load the dryer by the amount of space items take up. not by

their weight.

'

Do not overload the dryer. This causes uneven drying and

wrinkling.

Cycle lips

Dry most loads using the preset cycle settings.

Refer to the Auto Dry chart or Manual Preset Cycle Settings

chart (in the 'Cycles"

section) for a guide 10 drying various

loads.

Drying temperature

and Auto Dry Level are preset when

you choose an Auto Dry Cycle. You can select a different

dryness level, depending

on your load, by pressing Auto

Dry Level and choosing More or Less.

If you wish to adjust the cycle length of a Manual

Cycle,

press More Time or Less TIme. Adjust the temperature

of

a Manual Cycle by pressing Temperature until the desired
temperature

is selected.

NOTE: You cannot choose an Auto Dry Level with Manual
Cycles.

Drying and Cycle Tips

Select the correct cycle and dryness level or temperature

for your

load. If an Auto Dry Cycle is running. the display shows the

estimated

cycle time when

your

dryer is automatically

sensing

the dryness level of your load. If a Manual Cycle is running, the

display shows the exact number of minutes remaining in the
cycle.

.

Coel Down tumbles the load without heat during the last few
minutes of all cycles. Coel Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.

Drying lips

Follow care label directions when they are available.

If desired,

add

a fabric softener sheet. Follow package

instructions.

I

To reduce wrinkling, remove the load from the dryer as soon

I

as tumbling stops. This is especially important for pennanent
press, knits. and synthetic fabrics.

Avoid drying heavy work clothes together wrth lighter fabrics.

This could cause overdrying of lighter fabrics and lead to

increased shrinkage or wrinkling.

To use a Manual Cycle

Select a Manual Cycle.

Press MORE TIME or LESS TIME until the desired drying

!me is displayed. Tap MORE TIME or LESS TIME and the
time will change by 1-minute intervals. Press and hold

MORE TIME or LESS TIME and the time will change by

5--minute intervals.

NOTE: The More TIme and Less TIme features can be
used only wrth Manual Cycles.

OMOll!TI~E

OUSSTIME

Press TEMPERATURE until the desired temperature

glows.

NOTE: During a Manual Cycle, you can change the settings

for TIme. Temperature. WRINKLE GUARD" and End of Cycle
Signal. Press PAUSE/CANCEL twice to stop the dryer and
clear the settings. Selec1 another cycle or option.

(OPTIONAL STEP) If desired, select OPTIONS. For more
details, see "Options."

(OPTIONAL STEP) If desired, set the END of CYCLE SIGNAL.
Select HIGH or LOW to alert you when a cycle ends.

Press and hold START for approximately

3 seconds until

dryer starts. Be sure the door is closed.

If you do not press Start wrthin 5 minutes of selecting the

cycle, the dryer automatically

shuts off.

If you wish to end your drying cycle after pressing Start,

press PAUSE/CANCEL twice.

Stopping Your Dryer

I

stop your dryer at any lime

'ess PAUSE/CANCEL twice or open the door.

Pausing or Restarting

I

pause the dryer at any lime

pen the door or press PAUSE/CANCEL

once.

I

restart the dryer

ose the door. Press and hold START until dryer starts.

DTE: Drying will continue from where the cycle was interrupted
~ou close the door and press Start within 5 minutes. If the cycle

interrupted

for more than 5 minutes. the dryer will shut off.

llect new cycle settings before restarting the dryer.

Control Locked

,is feature allows you to lock your settings to prevent
,intended use of the dryer. You can also use Ihe Control Locked
ature to prevent unintended

cycle or option changes during

yer operation.

, enable the Control

Locked

feature:

ess and hold AUTO DRY LEVEL for 3 seconds. Control Locked
)ws and a single beep tone is heard. To unlock, press and hold
JTO DRY LEVEL for 3 seconds. The indicator light turns off.

Super Capacity Dryers

Heavy Wor!< Clothes

4 jeans
4 workpants

4 workshirts

Towels

10 bath towels
10 hand towels

Mixed Load

3 sheets (1 king, 2 twin)
4 pillowcases
3 shirts
3 blouses

2 sweatpants
2 sweatshirts

14 washcloths

9 T-shirts
9 shorts

10 handkerchiefs

Summary of Contents for Elite HE4 110.8586 Series



























Reviews: