Kenmore 796.40019 Service Manual Download Page 11

Page: 11 / 60

TEST OPERATION

Preparation for
washing.

• Connect the power plug to

the outlet.

• Connect the inlet hose.

Press the
START/PAUSE button.

•

Listen for a click to determine if
the door has locked.

Check the water heating
function.

•

Press the WASH/RINSE button
and the present temperature will
be displayed.

Check the automatic
reverse rotation.

Check the water supply.

•

Check if water is supplied
through the detergent dispenser.

Check the drain and spin
functions.

•

Power off and the power on.

•

Press the SPIN SPEED button.

•

Press the START/PAUSE button.

•

Check the spin and drain

functions.

Press the
START/PAUSE button.

Water removal.

•

If SERVICE is needed during

check, remove the remaining

water by pulling out the hose cap.

Press the POWER button.

•

Listen for a click to determine

if the door is unlocking.

•

Check if the drum rotates
clockwise and counterclockwise.

Summary of Contents for 796.40019





























































Search results

Summary of Contents for 796.40019

Reviews:

Related manuals for 796.40019

Brands by name

Popular brands

Kenmore 796.40019, Service Manual

Search results

Summary of Contents for 796.40019

Reviews:

Related manuals for 796.40019

Brands by name

Popular brands