Kenmore 625.75116 Use & Care Manual Download Page 4

Page: 4 / 26

Questions? Call the Kenmore Water Line 1-800-426-9345 or visit www.kenmorewater.com

Specifications & Performance Claims

This system conforms to NSF/ANSI Standard 44 for the specific performance claims as

verified and substantiated by test data.

Variable Salt Dose:

The salt dose is selected by the electronic controls at regeneration

time based on the amount needed.

SPECIFICATIONS

Model No. 625.75116

Model Code

150

Rated Softening Capacity (Grains @ Salt Dose)

8,300 @ 1.7 lbs.

20,400 @ 6.5 lbs.

24,400 @ 11.0 lbs.

Rated Efficiency (Grains/Pound of Salt @ Minimum Salt Dose)

4,880 @ 1.7 lbs.

Water Used During Regeneration @ Minimum Salt Dose

2.3 gallons/1,000 grains

Total Water Used Per Regeneration @ Maximum Salt Dose

26.6 gallons

Rated Service Flow Rate

7.3 gpm

Amount of High Capacity Ion Exchange Resin

0.68 cu. ft.

Pressure Drop at Rated Service Flow

15 psig

Water Supply Max. Hardness

70 gpg

Water Supply Max. Clear Water Iron

3 ppm

Water Pressure Limits (minimum / maximum)

20 - 100 psi

Water Temperature Limits (minimum / maximum)

5 - 49 °C

Minimum Water Supply Flow Rate

3 gpm

Maximum Drain Flow Rate

0.9 gpm

This model is efficiency rated. The efficiency rating is valid only at the minimum salt dose. This softener has a

demand initiated regeneration (D.I.R) feature that complies with specific performance specifications intended to mini-

mize the amount of regenerant brine and water used in their operation.

This softener has a rated softener efficiency of not less than 3,350 grains of total hardness exchange per pound of salt

(based on sodium chloride) and shall not deliver more salt than its listed rating or be operated at a sustained maxi-

mum service flow rate greater than its listed rating. This softener has been proven to deliver soft water for at least ten

continuous minutes at the rated service flow rate. The rated salt efficiency is measured by laboratory tests described

in NSF/ANSI Standard 44. These tests represent the maximum possible efficiency that the system can achieve.

Operational efficiency is the actual efficiency after the system has been installed. It is typically less than the rated

efficiency, due to individual application factors including water hardness, water usage, and other contaminants that

reduce a softener's capacity.

PERFORMANCE CLAIMS

Contaminant

Influent Challenge Level

Maximum Allowable

Product Water Level

Barium

10 ±10% mg/L

2.0 mg/L

Radium 226/228

25 pCi/L

5 pCi/L

Summary of Contents for 625.75116



























Search results

Summary of Contents for 625.75116

Reviews:

Related manuals for 625.75116

Brands by name

Popular brands

Kenmore 625.75116, Use & Care Manual

Search results

Summary of Contents for 625.75116

Reviews:

Related manuals for 625.75116

Brands by name

Popular brands