28
5
/
16
"
Side Panel
Door Open+
21
3
/
4
"
35
5
/
8
" -
36
3
/
8
"
30"
31
5
/
16
"
Min.
cutout
width
3
/
4
"
3
/
4
"
31
1
/
2
"
Formed or tiled
countertop
trimmed 3/4" back
at front corners of
countertop opening.
21
3
/
4
" min.**
22
1
/
8
" max.
CABINET
FRONT
1
1
/
8
"
22
7
/
8
" min.
††
23
1
/
4
" max.
COUNTERTOP PREPARATION
The cooktop sides of the range fit over the cutout edge of your countertop. Countertop must be level.
If you have a square finish (flat) countertop, no countertop preparation is required. Cooktop sides lay directly on edge of countertop.
Formed front-edged countertops must have molded edge shaved flat 3/4" from each front corner of opening.
Tile countertops may need trim cut back 3/4" from each front corner and/or rounded edge flattened.
If the existing cutout width is greater than 30 1/16", reduce the 3/4" dimension.
Shave Raised
Edge To Clear
31
1
/
2
" Wide
Cooktop.
1
1
/
2
" Max.
13"
30" Min.
For existing 29" cutout width
opening, you must call the Sears Service
Center for optional thinner side panels.
Also you must prepare the countertop
edge as shown in “Counterdepth
Preparation”.
Locate Cabinet
Doors 1" Min. From
Cutout Opening
18" Min.
Approx. 1
7
/
8
"
30" Min.*
30"
†
±
1
/
16
"
35
5
/
8
" Min.
36
5
/
8
" Max.
24" Min.
21
3
/
4
"
Min.**
22
1
/
8
"
Max.
Grounded Junction Box or Wall Outlet Should Be
Located 8" to 17" (20.3 - 43.2 cm) From Right of Cabinet
and 2" to 4" From Floor
††For cutouts below 22 7/8", applaince will slightly show out of the cabinet.
**Note: Minimum cutout depth is increased to 24" with optional backguard.
Note: Rear Top Filler Kit ships with product
Do not pinch the power supply cord or flexible gas conduit between the range and the wall.
Do not seal the range to the side cabinets.
*Note: 24" min. clearance between the cooktop and the bottom of the cabinets when the bottom
of the wood or metal cabinet is protected by not less than 1/4" flame retardant millboard covered
with not less than No. 28 MSG sheet metal, 0.015" stainless steel, 0.024" aluminum, or 0.020"
copper. 30" min. clearance when the cabinet is unprotected.
†Note: To avoid cooktop glass breakage for cutout with more than 30 1/16", make sure appliance
is centered in the counter opening while pushing it in. Raise leveling legs at maximum position,
insert the appliance in the counter and then level. Make sure the unit is supported by the leveling
legs and not by the cooktop glass itself.
+Allow at least 19 1/4" clearance for door depth when it is open.
page 2 of 2
Effective 09/14/09
09909
Because of our continuous program of product improvement, Sears
reserves the right to change materials and specifications without
notice. Consult installation instructions packed with the product for
final dimensional data. For complete warranty information, contact
your local Sears Commercial Account Manager.
22-4676X.PDF
slide-in ranges
| 22-46762/3/4/9
Because of our continuous program of product improvement, Sears
reserves the right to change materials and specifications without
notice. Consult installation instructions packed with the product for
final dimensional data. For complete warranty information, contact
your local Sears Commercial Account Manager.
22-49614,
22-49616
22-49624,
22-49626
All ranges are equipped with an
Anti-Tip device. The installation of
this device is an important, required
step in the installation of the range.
RANGE CORD REQUIRED
Order
Wire
Length
22-49614
3
4 ft.
22-49616
3
6 ft.
22-49624*
4
4 ft.
22-49626*
4
6 ft.