Kenmore 111.7303 Series Use & Care Manual Download Page 27

26

27

HUMIDITY CONTROLLED CRISPER

The crispers provide fresher tasting fruit and vegetables 

by letting you easily control humidity inside the drawer.

You can control the amount of humidity in the moisture 

sealed crispers crispers by adjusting the control to any 

setting between 

VEGETABLES

 and 

FRUIT

.

-  Slide the Humidity Control toward “hi” to keep moist air 

in crisper for best storage of fresh, leafy vegetables.

-  Slide the Humidity Control toward “lo” to release moist 

air from crisper for best storage of fruit.

REMOVING THE HUMIDITY CONTROLLED CRISPER
1.  

To remove, pull the drawer 

out to full extension.

2.  

Lift the front of the crisper 

up, then pull it straight out.

3.  

To install, slightly tilt up the front, insert the drawer into 

the frame and push it back into place.

FREEZER SECTION

PULLOUT FREEZER DRAWER

1.  

To remove, pull the freezer 

drawer out to full extension. 

Lift out the ice bin if present. 

Tilt the front of the pullout 

freezer drawer up and then 

lift drawer out. 

 

CAUTION

: Pinch hazard! Keep hands and feet clear 

of the bottom of the freezer drawer when opening and 

closing. 

2.  

To replace, hold pullout freezer drawer with back 

angled down. Insert the back rollers over the front edge 

of the runers built into the sides of the freezer cabinet. 

Slide the drawer back and into place. Fit ice bin back 

into pullout freezer drawer. 

 

WARNING

: When the pullout drawer is removed, there 

is enough room in the lower freezer drawer for a child or 

pet to crawl inside. To prevent accidental child and pet 

entrapment or suffocation risk, DO NOT allow children or 

pets to touch or go near the lower freezer drawer. 

Temperature Controlled Pantry Drawer  

(model 7330* only)

The Temperature Controlled Pantry Drawer provides 

storage space with a variable temperature control that 

can keep the compartment colder than the refrigerator 

section. This drawer can be used for large party trays, deli 

items, and beverages. (This drawer should not be used for 

vegetables that require high humidity).

Press Select button to choose between Produce, Deli or 

Meat. 

26 page same with 7304*, but 
Temp control zone added

The Temperature Controlled Pantry Drawer provides storage space with a variable temperature 

control that 

can keep the 

compartment colder than the refrigerator section. This drawer can be used for large party trays, deli items, and 
beverages. (This drawer should not be used for vegetables that require high humidity).

Press Select button to choose between Produce, Deli or Meat. 

Temperature Controlled Pantry Drawer

DOOR BIN

The door bins are removable for easy cleaning and 

adjustment.

1.  

To remove the bin, simply lift the bin up and pull 

straight out.

2.  

To replace the bin, slide it in above the desired support 

and push down until it snaps into place.

  

NOTE: 

Some bins may vary in appearance and will 

only fit in one location.

  

CAUTION

: Do not overfill or pack items too tightly 

into door bins. Doing so may cause damage to the bin 

or personal injury if items are removed with excessive 

force.

en-us

15

Temperature unit

The temperature can be displayed in

degrees Fahrenheit (°F) or

Celsius (°C).
After the appliance is switched on, the

temperature appears in degrees

Fahrenheit  (°F).

To set the temperature unit:

Press ”alarm/lock” for 2 seconds.
The ”Panel lock” symbol appears.

Press and hold ”super/quick ice” for

15 seconds until the temperature unit

switches.

Refrigerator

compartment

WARNING

Risk of explosion!

Never store products containing
flammable propellants (such as

spray cans) or explosive or easily
combustible substances in the
appliance.

Bottles containing a high
percentage of alcohol must be
tightly sealed and stored in an
upright position.

The refrigerator compartment

temperature can be adjusted between

35 °F (+2 °C) and 46 °F (+8 °C).
We recommend a setting of 39 °F

(+4 °C).
Perishable foods should not be stored

at temperatures higher than 39 °F

(+4 °C).

Using the refrigerator

compartment

For storage of ready meals, cakes

and pastries, canned food,

condensed milk, cheese, spreads,

sauces, dips and eggs.

Follow these guidelines

when storing food:

- Allow warm food and drinks to cool

down outside the appliance.

- Place food in airtight containers to

prevent it from losing its flavor or

drying out.

- To prevent poor air circulation in

the appliance, do not block

ventilation openings with food.

- Avoid contact of oil and grease with

plastic parts and door seal.

Vita Fresh

compartment

(not included on all models)
The temperature inside the Vita Fresh

compartment is kept at almost 32 °F

(0 °C). The low temperature provides

optimum storage conditions for

perishable food.

Food can be stored much longer in

the Vita Fresh compartment than in

the regular refrigerator compartment

without losing its freshness.

The Vita Fresh compartment is

covered by a special humidity filter.

The special humidity filter optimizes

the humidity in the Vita Fresh

compartment. Depending on how full

the Vita Fresh compartment is, the

humidity can reach up to 90 percent

which is ideal for all garden and field

products such as vegetables,

lettuces, herbs and fruit.

Vita Fresh is suitable for:

Basically any food that is fresh and is

to be kept fresh longer, such as meat

and meat products, fresh fish,

seafood, milk, butter, soft cheese,

cottage cheese, fruit and vegetables.

Vita Fresh is not suitable for:

Fruit and vegetables sensitive to cold,

such as tropical fruits, avocados,

papayas, passion fruit, eggplant,

cucumbers, bell peppers as well as

fruit that has to ripen, green tomatoes

and potatoes.

When buying food, please

note:

The ”freshness at purchase” is

important for the storage life of your

food. In general, the fresher the

products are when placed in the

Vita Fresh compartments, the longer

they will stay fresh. Therefore, when

purchasing food, always check how

fresh it is.

Removing the Vita Fresh

drawers

1. Pull out the Vita Fresh drawers as

far as possible.

2. Lift up the front of the Vita Fresh

drawers and pull them out.

3. Inserting the Vita Fresh drawers:

Insert the Vita Fresh drawers into

the rail and push toward the back.

en-us

16

Deli drawer

The temperature in the deli drawer is

kept at a constant temperature just

below freezing. This provides

optimum storage conditions for meat

and meat products, fish, seafood,

dairy products as well as hard and

soft  cheese.

NOTICE

Never store foods that are sensitive

to cold in the deli drawer.

Removing the deli drawer

1. Pull out the deli drawer as far as

possible.

2. Lift up the front of the deli drawer

and pull it out.

3. Inserting the drawer: Insert the deli

drawer into the rail and push

toward the back.

Variable interior

design

Glass shelves

The adjustable glass shelves can be

removed.

You can pull out the adjustable glass

shelves and place them at varying

heights.

Removing a glass shelf

Lift up and pull the shelf toward you.

Unhook and then remove the shelf.

Installing the glass shelf

Lift up the front of the shelf and insert

the hooks into the openings at the

desired height. Lower the front of the

shelf.

Small top glass shelf

The glass shelf can be removed and

placed in the holder underneath the

ice maker. This provides room to

place taller items such as tall bottles

next to the ice maker.

Door storage compartments

To remove door storage

compartments:

Lift door compartment and take it out.

To install door storage

compartments:

Place the compartment above the

bracket at the desired height and

press down.

Butter and cheese

compartment

Raise the cover on the butter and

cheese  compartment.

To remove the butter and cheese

compartment:

Lift up the compartment and take it

out.

To install the butter and cheese

compartment:

Place the compartment above the

bracket at the desired height and

press down.

Egg compartment

USING YOUR REFRIGERATOR

F706-10(�)(Kenmore).indd   27

2019-03-04   �� 10:40:29

Summary of Contents for 111.7303 Series










































Reviews: