background image

EN

FastMig KMs as + arcFeed

3.4.2 

GND

ArcFeed

COnneCtiOn tO the Mains supply

3.5 

FastMig power sources are delivered as standard with 5 meters of mains power cable. No 

mains plug is fitted at the Kemppi factory.

NOTE!  

If local country based regulations state an alternative power cable is required, the mains 

cable must be replaced in conformity with the regulations. Connection and installation of the 

mains cable and plug, should only be carried out by a suitably qualified person.

Remove the machine cover plate to enable mounting of a mains cable. FastMig Pulse power 

sources can be connected to the mains supply of 400 V 3~ .

if changing the mains cable take into consideration the following:

The cable is entered into the machine through the inlet ring on the rear panel of the 

machine and fastened with a cable clamp. The phase conductors of the cable are coupled 

to connectors L1, L2 and L3.  The earth protection coloured green-yellow is coupled to the 
marked connector   . If you are using 5-lead cable, do not connect the neutral conductor.

Sizes of the mains cables and fuse ratings for the machine at 100 % duty cycle are specified in 

the table below:

Rated voltage

Mains voltage range

Fuses, slow-blow

Connection cable *) mm²

KMS 300 400 V 3~

360 V… 440 V

20 A

4 x 6.0 S

KMS 400 400 V 3~

360 V… 440 V

25 A

4 x 6.0 S

KMS 500 400 V 3~

360 V… 440 V

35 A

4 x 6.0 S

*) In cables of S type there is a protective grounding conductor coloured green-yellow.

8

FastM

ig KMS 400 AS / © Kemppi O

y / 1021

Summary of Contents for KMS 400 AS





















Reviews: