background image

7

Rooftop installation

Rooftop installation

If the outdoor unit is installed on a roof structure, be sure to level 
the unit.

Ensure the roof structure and anchoring method are adequate for 
the unit location.

If the outdoor unit is installed on roof structures or external walls, 
this may result in excessive noise and vibration, and may also be 
classed as non-serviceable installation.

Pipe Length Elevation and Additional Quantity of Gas

Model Number Discharge Pipe  

Diameter

Suction Pipe 

Diameter

Standard 

Length (m)

Maximum 

Length (m)

Maximum  

Height (m)

Additional 

Refrigerant (g/m)

KSV25HRF

Ø6.35 mm (1/4”)

Ø9.52 mm (3/8”)

7.5

15

10

16

KSV35HRF

Ø6.35 mm (1/4”) 

Ø9.52 mm (3/8”)

7.5

20 

10 

16

KSV52HRF

Ø6.35 mm (1/4”) 

Ø12.70 mm (1/2”) 

7.5

25 

10 

16

KSV70HRF

Ø6.35 mm (1/4”) 

Ø15.88mm (5/8”) 

7.5 

25 

10 

40

KSV80HRF

Ø6.35 mm (1/4”) 

Ø15.88mm (5/8”) 

7.5

30 

10 

40

KSV25CRF

Ø6.35 mm (1/4”) 

Ø9.52 mm (3/8”)

7.5

15 

10 

12

KSV35CRF

Ø6.35 mm (1/4”) 

Ø9.52 mm (3/8”) 

7.5

20 

10 

12

KSV70CRF

Ø6.35 mm (1/4”) 

Ø15.88 mm (5/8”) 

7.5

25 

10 

12

WARNING

caution

• 

 The outdoor unit is charged with the refrigerant for standard 

pipe length of 7.5m. 

• 

 When the connecting pipe length is longer than the standard 

length, additional refrigerant should be added into the unit 

according to the above table through the service port on 3-way 

service valve on the outdoor unit.

• 

 PLEASE MAINTAIN THE SHORTEST DISTANCE (3 TO 5 

METRES) AND SHORTEST MISALIGNMENT POSSIBLE 

BETWEEN THE INDOOR AND OUTDOOR UNITS.

• 

 The maximum allowance length and height is based  

on reliability. Exceeding the maximum may cause poor 

performance or malfunction. 

• 

 When the level difference between indoor and outdoor units 

is greater than the maximum height of 10 metres, or when 

the outdoor unit is installed above the indoor unit, an oil trap 

should be installed every 5-7 metres.

maximum length

maximum length

oil trap

maximum height

maximum height

piping length under 7.5m

piping length 7.5m or more

A

A

B

B

indoor unit

indoor unit

outdoor unit

outdoor unit

Summary of Contents for KSV25CRF





























Reviews: