Kellfri 35-VKMATV150HXL Operator'S Manual Download Page 7

7

TABLE OF CONTENTS

7

WARNING!

Never use a tool or product with defective safety equipment.

SURROUNDINGS

Check and make sure that the area is clear of people, children and objects before switching 

on or using the equipment. Risk of serious personal injury. Be especially careful if children are 

in the area where the equipment is being use or stored. Check that there are no low-hanging 

power lines within the work area. Be careful when working on slopes and near ditches.

Always work alone with equipment designed for single - purpose tools/products. Never have 

junk/debris lying in your work area. Have workspaces clean. Always respect the risk zone.

DANGER!

Children in the area should be  supervised!

INCASE OF EMERGENCIES

In case of an emergency please dial 999.

Keep cell phone or emergency phone available specially when working alone. First aid kit and 

fire extinguishers must be kept easily accesable during all work, maintenance and service.

PERSONAL PROTECTION

Always  use  suitable  protection  equipment.  Do  not  wear  loose  clothing  or  jewellery  while  

working with the equipment. Long hair should be tied up when working equipment that has

moving parts. Use protective gloves as there is a risk of burns if any hot surfaces are touched 

such as exhaust pipes, and avoid getting oil and petrol on skin. Ear defenders must be worn 

whilst the engine is running.

Summary of Contents for 35-VKMATV150HXL





























Reviews: