background image

3

Table of contents

INTRODUCTION

 

Thank you for choosing a product from Kellfri AB. Compliance with the safety instructions,  

operating manual and sound common sense will guarantee many years of enjoyment  

using the product. Kellfri’s equipment and products are aimed at self-employed farmers,  

horse enthusiasts and other country dwellers with stringent performance demands.

PRODUCT INFORMATION

• 

8 pcs (34-FHH8) 

• 

Grille gates 

• 

Adjustable roof height 

• 

Adjustable base supports – 2 heights

• 

2 base supports provide good stability 

• 

Adapted for round/large bales

Grille gates made of sturdy tubing with 50 mm spacing between the tubes, provide a high 

level of safety and ensure the roughage stays in the feeder. Feed can be replenished quickly 

and easily by opening any of the four grille gates which open out to the side. Two 325 m wide 

feed openings on each side of each grille gate ensure minimal feed waste. The roof is height-

adjustable to offer the best protection against precipitation, and is also fitted as standard with 

a protection arch all the way around to offer the horses maximum safety. Two adjustable base 

supports ensure that the feeder is stable and does not sink into the ground in wet conditions. 

There are in-built pallet fork insertion points to move the feeder safely and stably, which also 

means there are no protruding brackets, thus avoiding injuries. The entire feeder is galvanised. 

Using the feeder offers feed savings, top hygiene and healthier animals. A feeder designed 

for horses, smooth tubular pipes used in railing, protective tubular pipes used in roof corners 

with two feed openings on each side. Lightweight design, openable gates on all sides for 

easy refilling of fodder and with forklift pockets at the base to ensure stable and safe removal.  

Full roof for maximum weather protection. 

AREA OF USE

Only intended for feeding livestock, can be used for horses. 

Follow the Swedish Board of Agriculture’s rules (

jordbruksverket.se).

TECHNICAL DATA

34-FHH8

Width

1500 mm

Length

1500 mm

Height

2600 mm

Weight

245 kg

Feed openings

8 pcs.

Warning! 

Different animals/individuals have different conditions, behaviours and temperaments. 
Where there is a suspicion that the individual may be injured, action should be taken prior 
to use to minimise the risk of injury when using the combination of animals/feeder.

Summary of Contents for 34-FHH8





















Reviews: