background image

Section 3: Software Reference 

S530 Parametric Test Systems Frequency Analysis Option Manual 

 

3-12 

S530-923-01 Rev. A / January 2014 

 

Format

  int freq_detect_peaks(double min_level, double lower_bound, double upper_bound, 

double *freq_array, int nPeaks, double *amp_array, int nPeak1); 

Parameters

min_level

 

Minimum amplitude in dB; the peak detected must be higher than the min_level 

lower_bound

 

The measured peak will be ignored if the ratio of measured freq vs. returned peaks is NOT less than the 

lower_bound 

lower_bound

 

The measured peak will be ignored if the ratio of measured freq vs. returned peaks is NOT greater than the 

upper_bound 

nPeaks

 

Number of peak frequencies to be returned; zero will be returned to fill up the output array when the 

number of detected peaks is less than nPeaks 

nPeak1

 

Must be the same as nPeaks 

 

Returns

freq_array

 

array output of measured peak frequencies in Hz 

amp_array

 

amplitude of the measured peak frequencies in dB 

Remarks

:  

The spectrum analyzer must be initialized before using the 

freq_detect_peaks

 command. 

Example

   

double freq; 

   

double ampltd; 

   

   

   

   

Status1 = freq_init( ); 

   

Status2 = freq_setup(20e6, 850e6, 1e6); 

   

status3 = freq_detect_peaks(6e-4, 0.7, 1.4, &freq, 5, &ampltd, 5); 

 

freq_selftest 

Purpose

:    

Performs an internal self-test of the scope card. 

Format

 

   

 

int freq_selftest(); 

Parameters

:  

None 

Returns

:  

This command returns a 1, if executed without error; otherwise, a negative 

number is returned to indicate an error. 

Remarks

:    

The unit must be initialized before using 

freq_selftest

 command. 

Example

   

 

Status1 = freq_selftest(); 

 

Summary of Contents for S530
























Reviews: