Keithley 4200-CVU Quick Start Manual Download Page 3

Model 4200-CVU Quick Start Guide 

PA-952 Rev. A / November 2007 

Quick-start instructions 

Step 1: Unpack your Model 4200-SCS 

The box contains: 

ƒ

 

Model 4200-SCS Semiconductor Characterization System, with the Model 4200-CVU card integrated into 
the mainframe. 

NOTE:   How to lift the Model 4200-SCS: 

 

• Lift from the bottom, not from the front bezel. 

 

• Set it on a bench or install it in a rack using the optional slide rack mounting kit. 

ƒ

 

Keyboard with built-in pointing device 

ƒ

 

Two triax cables for each  source-measure unit (SMU) 

ƒ

 

Four red SMA to SMA cables for the Model 4200-CVU 

ƒ

 

Connectors: Four SMA to BNC adapters; 2 BNC tees 

ƒ

 

Y-Cable: Use to connect the keyboard to the mainframe 

ƒ

 Power 

cord 

ƒ

 

Model 4200-SCS KTE Interactive CD-ROM 

ƒ

 

Model 4200-SCS Complete Reference CD-ROM 

 

Step 2: Make basic system connections (power cord, keyboard, and optional 
printer) 

Basic system connections to the Model 4200-SCS (shown in Figure 2) include the keyboard (which has a built-
in pointing device), the supplied power cord, and an optional printer. If you are using  a USB printer, connect it 
to the USB port. 

WARNING 

Plug the female end of the supplied power cord into the Model 4200-SCS, but 
DO NOT connect the male end to line power at this time. Steps 2 and 3 in the 
QSG must be performed with the line power disconnected. 

Figure 2: System connections 

Keithley

4200-SCS

Mouse/Keyboard

Connector

Parallel

Connector

Keyboard

Shielded

Parallel

Cable

Parallel

Printer

* v1.1 USB connector (Windows
  XP Professional operating
  system) – If using a USB printer,
  connect it to the USB port.

USB

Port*

INSTRUMENT

CONNECTIONS

SMU ONLY

SMU  AND  GNDU

GNDU

COM  1

INSTRUMENTS

SLOT

8

SLOT

7

SLOT

6

SLOT

5

SLOT

4

SLOT

3

SLOT

2

SLOT

1

LPT  1

INSTALLATION

CATEGORY
I

S
E
N
S
E

F
O
R
C
E

C
O
M
M
O
N

SENSE  LO

GUARD

SENSE  LO

COMMON

COMMON

FORCE

SENSE

GUARD

4200

SMU

SENSE  LO

SENSE

FORCE

PA  CNTRL

KEITHLEY

4200

SMU

SENSE  LO

SENSE

FORCE

PA  CNTRL

KEITHLEY

4210

SMU

SENSE  LO

SENSE

FORCE

PA  CNTRL

KEITHLEY

4210

SMU

SENSE  LO

SENSE

FORCE

PA  CNTRL

KEITHLEY

4200

TM

INTLK

IN

OUT

KEITHLEY

Y-Cable (supplied)

Power Cord

(supplied)

LPOT

HCUR

LCUR

HPOT

4200

CVU

KEITHLEY

4200-CVU

Card

 

Summary of Contents for 4200-CVU













Reviews: