EQUIPMENT YOU NEED
Before assembling your new Keiser M3 indoor cycle obtain the following tools:
Torque wrench (Minimum 45 Nm / 35 ft-lb)
4” extension
15mm open-end wrench
16mm, or 5/8” open-end wrench
#2 Phillips screwdriver
15mm crowfoot
16mm, or 5/8” crowfoot
5mm Allen Wrench
6mm Allen Wrench
Paste or spray wax (used to clean after assembly)
Clean cloth
NOTICE
Users, agents or anyone directing the use of this equipment shall determine the
suitability of the product for its intended use, and said parties are specifically put on
notice that they shall assume all risk and liability in connection herewith.
555500 B
UNPACKING THE BIKE
Carefully remove the bike from the cardboard box. Lay-out all the components and check to
assure all parts are present and undamaged. If parts are missing or damaged contact your
local dealer, distributor or Keiser Corporation Service Department.
NOTE:
The substitution or modification of any part or component, other than what is
approved by Keiser, will void your warranty.
After unpacking and verifying parts, you are ready to start your assembly. You need an area
that is free of dirt, dust or other foreign material that could impair the assembly of your
bike.
Always follow the steps in this manual as you assemble your bike. Do not skip, substitute or
modify any steps or procedures of this assembly, as doing so could result in personal injury
and will void your warranty. We have put a number of precautions in this manual.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, could
result in serious injury. By not heeding these warnings, the warranty will be void.
NOTE:
Informs you about things we recommend you do or are aware of, before performing
the assembly. These notes are placed in the manual to aid you during a certain procedure or
to make you aware of any general mandatory actions or information.
ASSEMBLY MANUAL
BEFORE ASSEMBLING
A
B
C
E
F
G
H
K
J
L
NOTE: Since we are always striving to improve our products; our products are
subject to change without notice.
CHECKING FOR PROPER OPERATION
Pre-Ride Checklist
Please inspect bike carefully and thoroughly before riding.
�
All Parts Correctly Installed
�
Acorn Nuts Torqued At 45 Nm (35 ft-lbs)
�
Pedals Loctited and Torqued To 45 Nm (35 ft-lbs)
�
All Screws and Nuts Properly Torqued and Tightened
�
Handlebar and Seat Adjustments Operate Properly
�
Bike Has Been Polished With Paste or Spray Wax and a Clean Cloth
�
Computer Installed and Calibrated and In Working Order
(Models With Computers) (See “Calibrating The Computer”)
Test Ride
Your bike should now be ready to test ride.
1. Adjust the seat and handlebar for proper height and comfort.
2. Secure your feet in the pedals.
3. Move the shifter toward yourself and down and begin pedaling.
4. The computer should wake up and display “ODO” and total distance ridden
across the bottom. After approximately 10 secs “ODO” will change to gear
and trip.
5. Now move the shifter up and note the gear changing on the computer and the
resistance getting harder.
6. Ride at various speeds and resistances to check for noise and vibration.
7. Move the shifter to full forward position to check that the emergency brake
stops the flywheel from turning.
8. You have completed the test.
9. Enjoy your ride.
If you experience any problems please contact our Service Department
(USA) 1-800-888-7009 (International) 559-256-8000
www.keiser.com/service/
[email protected]
WARNING:
Perform the operation below before riding to make sure
the bike is fully operational. Failing to test a bike prior to normal
use will void your warranty and could result in serious injury.
PARTS INVENTORY
A) Handlebar Assembly
B) Base Frame
C) Bike Frame
D) Flywheel
E) 2-Pedals/1-Loctite 242
F) Hubcap
G) 4 Acorn Nuts
H) 4 Washers
J ) 5 Socket Head Cap Screws
M6x1 X 20 SS
K ) 2 Socket Head Cap Screws
M8x1.25 X 12 SS
L) Computer (models with computer only)
(800) 888-7009 keiser.com
