background image

USER MANUAL 

Spirit User manual 

 

page 5 

Mains switch 

The mains switch (see Figure 3 a) is located at the right hand side of the machine and has 3 positions: 

OFF 

All power to the machine is disconnected. 

NO HEAT 

The machine is connected to power, but power to the heating elements is disconnected. 
The machine functions but there is no heat and thus neither hot water nor steam 
pressure. The lack of steam pressure means that flow from the hot water spout is less 
than normal.  

ON 

Machine and heating elements are connected to power. 

 

  

 

Figure 3 a (left). Showing mains switch with its 3 positions, the right hand brew lever and steam lever 
on the right steam wand. 
Figure 3 
b (right). Showing hot water lever and -spout and a coffee boiler pressure gauge. 

 

Back light switch 

The LED

’s that illuminate the Spirit or customers logo on the back side of the machine can be turned 

ON or OFF. When the machines leaves the shop, the illumination is turned OFF to make sure that you 
use the switch at least once. The switch is located behind the right hand side front leg of the machine 
(see Figure 4). 

 

Figure 4

. Showing the switch that turns the back LED’s on and off (lever pointing down is OFF). 

 

 

hot water lever 

brew lever  steam lever 

mains 

switch 

steam 

wand 

hot water 

spout 

coffee 

pressure 

gauge 

back 

light 

switch 

Summary of Contents for Spirit DUETTE



























Reviews: