manualshive.com logo in svg

Kees van der Westen Slim Jim mirage, User Manual

Share
Download
Kees van der Westen Slim Jim mirage User Manual Download Page 12

USER MANUAL - operation 

Slim Jim User manual 

 

page 11 

 

 

 

 
Note that in the example above group 2 is at 45.6°C at moment of switching to ECO. As the ECO 
temperature of the coffee-boilers is 50°C, the boiler will continue to heat until 50°C is reached and the 
centre line will thus remain orange. 

 

Go to stand-by 

You have to leave the operational window to go to stand-by. In stand-by the controller is in sleeping 
mode and the machine does not operate. There are two stand-

by modes: “NO HEAT” and “ECO-

MODE

”. At “NO HEAT” there is no power to the heating elements and the boilers will (eventually) cool 

down to room-

temperature. At “ECO-MODE” the boilers will cool down to a lower set temperature and 

are then kept at that temperature (coffee boilers: 50°C, steam boiler: 70°C).  

operational window

 

 

 

 

 

 

 

 

touch 

 

 

 

 

 

 

 

 

menu window

 

 

 

 

touch 

 

 

 

 

 

 

 

 

 

 

 

 

stand-by window

 

 

choose “NO HEAT” 

or “ECO MODE”

 

 

 

touch 

touch 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

no-heat window

 

 

“NO HEAT”: the 

machine will cool 

down

 

 

 

 

 

 

 

 

eco window

 

 

“ECO”: the machine 

will settle at lower 

set temperature

 

 

 

 

touch 

or operate a 

Bastone/touchpad 

 

 

touching the central button at “NO HEAT” or “ECO” will 

return the machine to operation (first window

 

 

 

A machine set at ECO will also turn to normal operation when any of Bastone units or touchpads or 
mix-water switch is manipulated. 

This “first manipulation” will not result in starting a dispense. 

 

GROUP 1

93.4

GROUP 2

47.2

GROUP 3

93.2

STEAM

124.6

MENU

GROUP 1

93.4

GROUP 2

47.2

GROUP 3

93.2

STEAM

124.6

MENU

STAND

BY

EXTERNAL

SENSOR

CLEAN

PROGRAM

SETTINGS

13 : 57

NO

HEAT

ECO

MODE

EXIT

THURSDAY            13 : 57

TECH. ASSISTANCE

KEES VAN DER WESTEN

SLIM JIM

NO HEAT

THURSDAY  

13 : 57

TECH. ASSISTANCE

KEES VAN DER WESTEN

SLIM JIM

ECO

Summary of Contents for Slim Jim mirage


































Reviews:

No comments

Brands by name

Popular brands

Load more brands