background image

Next

Home

Back

17

The Cryomatic and its components are covered by warranty that they 
meet their performance standards and are free from any defects in 
materials or workmanship. Within 12 months from delivery by Keeler, 
the manufacturer shall at no charge to the customer, upon written 
notice from the customer, repair or replace any components which are 
defective in material or workmanship. 

The customer agrees that it shall have no remedy in the event of any 
breach of the foregoing warranty other than as provided above. This 
warranty is exclusive and in lieu of all other warranties, expressed or 
implied, and all implied warranties of merchantability or fitness for a 
particular purpose are expressly disclaimed.

The obligations of the manufacturer as set forth in this warranty are 
expressly conditional upon the following:-

(i)

 No alterations or repairs of any malfunction of the system shall 

be made to the system except by the manufacturer or his authorized 
representative, without the prior written approval of the manufacturer 
or his authorized representative (and in no case will the manufacturer 
assume responsibility for repairs or alterations made by those other 
than the manufacturer or his authorized representative).

And

(ii)

 The customer shall give notice to the manufacturer or their 

authorized representative of any malfunction of the system and shall 
not use the system in any surgical operation after they are aware of 
any malfunction.

(iii)

 The customer complies with manufacturer’s recommended 

Preventative Maintenance (see Section 8) and can provide proof of 
such action.

11. Warranty

12. Disposal

 

 

Ensure that this equipment is disposed of in accordance  

 

 

with local regulations. 

 

 

Please contact the supplier if in doubt.

Summary of Contents for Cryomatic

























Reviews: