Keba ServoOne CM Series Operation Manual Download Page 47

Page: 47 / 70

Electrical installation

Operation Manual ServoOne CM-L and ServoOne CM-A

ID no.: 1800.208B.1-00 Date: 03/2020

Electrical installation

4.11.2 Specification, connection "State" (X6)

Des.

Abbreviation

Specification

Details

X6/State

RO01NC = normally

closed contact

RO01CO = changeo-

ver contact

RO01NO = normally

open contact

RO01NC
RO01CO
RO01NO

Relay contact:

≤

50 V AC, 0.5 A max. (ohmic

load)

contact freely programmable

Factory setting = Active on error

TP00 =

test pulse signal 00

TP01 =

test pulse signal 01

GND =

reference ground

Signal driver outputs for in-

ternal usage for short-circuit

and cross-circuit checks on

the wiring to the safe inputs

on the axis controllers

See

Model Description SD0

ID no. 1400.402B.x-xx

EXP–

EXP+

Quick shutdown, mains

output.

If there is an error in the axis

group SO CM (BG1+2), the

expansion module sends a

quick shutdown signal to the

SO CM-A.

The cable to the expansion

module SO CM-E is connect-

ed to this connector.

Quick shutdown

(emergency shutdown)

Two-core cable

Polarity reversal protection

Cross-section: max.

1.5 mm

without ferrules

Max. 6 bus users

GND

Power failure

Signals power failure with a

24 V signal

4.11.3 Specification, relay contact (X5)

Des.

Abbreviation

Specification

Details

X5/REL Output

RO02NO

= normally

open

contact

RO02CO

RO02NO

Relay contact: 230 V AC, 4 A

max. (ohmic load),

contact freely programmable

Factory setting = Operation of

main contactor

Key to the layout, ServoOne CM-L charging module

Item

Abbrevia-

tion

Designation

Details



LED red

(ERR)

LED green

(Voltage)

Supply unit error status (flashing

code)

Status mains supply available

See Section 5.1.1



XC OUT

Cross-communication

See Section 4.11.1 Specification,

cross-communication (X3)



State

Relay contact (RO01)

Digital outputs (TPO0, TPO1)

Quick shutdown EXP-/EXP+

Power failure PF

See Section 4.11.2

Specification, connection "State" (X6)



REL

Output

Relay contact (RO02)

See Section 4.11.3

Specification, relay contact (X5)



, ϑ

Connection for mains filter (

) and

mains choke temperature sensor

(

)

See “4.11.4 Specification, connection of

temperature sensor (X1)”



BR,

Connection for braking resistor

temperature sensor

See Section 4.11.4 Specification, connec-

tion of temperature sensor (X1)



Shield plate

Table 4.16

Key to layout, control connections ServoOne CM-L charging module

4.11.1 Specification, cross-communication (X3)

Des.

Abbreviation

Specification

Details

XC OUT

Cross-communication output (RJ10

connector), internal RS485 network for

communication with axis controllers

See

Operation Manual SO CM

ID. no. 1800.200B.x-xx

Summary of Contents for ServoOne CM Series







































































Search results

Summary of Contents for ServoOne CM Series

Reviews:

Brands by name

Popular brands

Keba ServoOne CM Series, Operation Manual

Search results

Summary of Contents for ServoOne CM Series

Reviews:

Brands by name

Popular brands