manualshive.com logo in svg

Keba D3DP 3 Series, Project Engineering Manual, Page: 25 / 82

Share
Download
Keba D3DP 3 Series Project Engineering Manual Download Page 25

D3­DP 3xx/x

Mounting and installation instructions

Project engineering manual V1.00

25

© KEBA

Information

The supply module must always be mounted to the left of the axis modules.
The highest power axis module should be close to the supply module. For
double and triple axis modules the total power counts.

Caution

Protection against hot surfaces in operation. Temperatures up to 85 °C can
occur on the rear of the device. Please maintain an adequate distance from
neighbouring assemblies, particularly above the heat sink.

CAUTION!

Protection against hot surfaces in operation. Provide adequate protection
against touching the heat sink.

5.1

EMC requirements

The essential EMC measures are already implemented in the design of the
devices in the form of optimised housing shielding, printed circuit board lay­
out, filter measures and selection of suitable connectors with shield plate. In
addition to the internal measures, the following installation measures are to
be noted:

●

To obtain the best result for effective EMC installation you should use a
well conductive mounting plate, which is well­earthed due to safety rea­
sons.

●

By mounting plates which are varnished, remove the coating from the
contact area! The devices themselves have a chromated zinc frame.

●

Use shielded cables: In 

15 Appendix

 are all cables listet, which are avail­

able at KEBA. It is recommended to use this cables, because all EMC
tests were executed with this cables and so they are tested accordingly.

●

EtherCAT connection between control module, supply module and axis
modules: The supply package of axis­ and supply modules also contains
EtherCAT connection cables, which enable connection to the left com­
munication partner. The order designations for longer RT­Ethernetcables
are listed in the appendix.

●

Additional shield contact for RT­Ethernet: See 

5.1.1 Requirements to the

connectors

5.1.1

Requirements to the connectors

The following connections are available in the system:

●

RT­Ethernet (RJ45) connectors

Summary of Contents for D3DP 3 Series



















































































Reviews:

No comments