KEB COMBIVERT S6 Series Instructions For Use Manual Download

Page: 28 / 66

3.2.2 control cabinet installation

Power dissipation for the control cabinet dimension =>

„Power dissipation“

. A lower value

can be used here depending on the operating mode/load.

Installation of the drive converter

For reliable operation, the drive converter must be installed without clearance

on a smooth, closed, bare metal mounting plate.

Mounting distances

Dimen-

sion

Distance in mm

Distance in inch

150

100

1.2

1) Distance to preceding elements in the cabinet

door.

Figure 2:

Mounting distances

If construction-conditioned the control cabinet cannot be without indoor ventilation, ap-

propriate filters must avoid suction of foreign objects.

Direction of the air

flow

Front and side view of the coolant inlet

Coolant outlet

Coolant inlet

Figure 3:

Control cabinet ventilation

DIMeNSIONS AND WeIGHTS

Summary of Contents for COMBIVERT S6 Series



































































Search results

Summary of Contents for COMBIVERT S6 Series

Reviews:

Related manuals for COMBIVERT S6 Series

Brands by name

Popular brands

KEB COMBIVERT S6 Series, Instructions For Use Manual

Search results

Summary of Contents for COMBIVERT S6 Series

Reviews:

Related manuals for COMBIVERT S6 Series

Brands by name

Popular brands