© Copyright 2012 KE2 Therm Solutions,Inc. . Washington, Missouri 63090
Quick Start with a TEV
Power up the newly installed controller
The
ROOM TEMP
display will show a blinking number. Use the
left or right arrow to move between digits, use the up or down
arrow to adjust the blinking digit higher or lower.
Once new setpoint is displayed, press and hold ENTER for 3
seconds
Now, the
DEFROST TYPE
is displayed. Wait until
ELEC
(Electric
Defrost) is displayed, if other than ELEC is needed, use the up
or down arrow to scroll through list and select
AIR, HOT GAS
COMP ON, HOT GAS COMP OFF
Once desired option is shown, press and hold ENTER key for 3
seconds.
VALVE TYPE
is displayed.
MECHANICAL
will appear.
Press and hold ENTER for 3 seconds.
The controller will now begin controlling the system.
Quick Start with a Custom EEV
Power up the newly installed controller
The
ROOM TEMP
display will show a blinking number. Use
the left or right arrow to move between digits, use the up or
down arrow to adjust the blinking digit higher or lower.
Once new setpoint is displayed, press and hold ENTER for 3
seconds
Now, the
DEFROST TYPE
is displayed. Wait until
ELEC
(Elec-
tric Defrost) is displayed, if other than
ELEC
is needed, use the
up or down arrow to scroll through list and select
AIR, HOT
GAS COMP ON, HOT GAS COMP OFF
Once desired option is shown, press and hold ENTER key for 3
seconds.
VALVE TYPE
is displayed.
MECHANICAL
will appear, use the
up or down arrows to scroll to
CUSTOM
.
Press and hold ENTER for 3 seconds.
REFRIGERANT
is displayed. 404A will appear. Use the up or
down arrows to view the other options.
Once the desired refrigerant is displayed, press and hold ENTER
for 3 seconds.
MOTOR TYPE
is displayed. Wait until
BIPOLAR
is displayed.
Use the up or down arrows to select either
BIPOLAR
or
UNI-
POLAR
Press and hold ENTER for 3 seconds.
MOTOR STEP RATE
is displayed. Wait until
200
is displayed.
Use the left and right arrows to move between the digits. Use
the up or down arrows to adjust the blinking digit higher or
lower.
Press and hold ENTER for 3 seconds.
MAX VALVE STEPS
is displayed. Wait until
1300
is displayed.
Use the left or right arrows to move between digits. Use the
up or down arrows to adjust the blinking digit higher or lower.
Press and hold ENTER for 3 seconds.
The controller will now begin controlling the system.
Quick Start with a Pre-programmed EEV
Power up the newly installed controller
The
ROOM TEMP
display will show a blinking number. Use
the left or right arrow to move between digits, use the up or
down arrow to adjust the blinking digit higher or lower.
Once new setpoint is displayed, press and hold ENTER for 3
seconds
Now, the
DEFROST TYPE
is displayed. Wait until
ELEC
(Electric
Defrost) is displayed, if other than ELEC is needed, use the up
or down arrow to scroll through list and select
AIR, HOT GAS
COMP ON, HOT GAS COMP OFF
Once desired option is shown, press and hold ENTER key for 3
seconds.
VALVE TYPE
is displayed.
MECHANICAL
will appear, use the
up or down arrows to scroll through pre-programmed EEV op-
tions.
Once the desired EEV is displayed, press and hold ENTER for 3
seconds.
REFRIGERANT
is displayed. 404A will appear. Use the up or
down arrows view the other options.
Once the desired refrigerant is displayed, press and hold EN-
TER for 3 seconds.
The controller will now begin controlling the system.
Step-by-Step QuickStart
Mechanical Valve TEV -
3 steps
Standard EEV -
4 steps
Custom EEV -
7 steps
Room Temp
Room Temp
Room Temp
Defrost Type
Defrost Type
Defrost Type
Valve Type
Valve Type
Valve Type
Refrigerant
Refrigerant
Motor Type (Unipolar/Bipolar)
Motor Step Rate
Max Valve Steps
