To access all settings, press the home button to go to the main menu of Peppa’s Play &
Learn Smart Watch.
Then press OK on the tools & settings icon
How to set time
1. Go to “Time Setting” using the arrows and press the OK button to select it.
2. Press on the left arrow to set hours and the right arrow to set minutes.
3. Then, when time is set, press OK to validate and apply your selection.
How to customise the clock
1. Go to “Clock Setting” using the arrows and press the OK button to select it.
2. Using the arrows select if you want an analog or a digital display.
3. If you chose an analog display, then you can chose between two different analog
clock designs by using the arrows.
4. If you chose a digital display, f irst using the arrows you can chose between a 12h or
24h display and then you can chose between two different digital clock designs by
using the arrows.
Ensure the OK button is pressed after each step to save and validate you choice.
How to customise the clock background
1. Go to “Background” using the arrows and press the OK button to select it.
2. Using the arrows select the background design you would like to use.
3. Press OK to save and validate.
How to set the volume
1. Go to “Volume Setting” using the arrows and press the OK button to select it.
2. Using the arrows select the volume level you would like to use.
3. Press OK to save and validate your choice.
How to set the brightness
1. Go to “Brightness Setting” using the arrows and press the OK button to select it
2. Using the arrows select the brightness level you would like to use.
3. Press OK to save and validate your choice.
How to set the alarm clock
1. Go to “Alarm Setting” using the arrows and press the OK button to select it.
2. Using the arrows set the hours then press OK to validate.
3. Using the arrows set the minutes then press OK to validate.
4. Using the arrows select On or Off and press OK to save and validate your choice.
Settings
About the Battery
Unit powered with
PTI PL062030P 3.7V 300mAh (1.11 Wh)
Li-Polymer Battery
Limited charge voltage 4.2V
Made in China
Cautions:
- Do not short-circuit
- Do not discard into Fire
- Do not charge or expose in temperature over 60
°
C, moisture or corrosive
environments
- Do not disassemble/open
- Do not swallow
Battery charging:
Peppa’s Play & Learn Smart Watch is equipped with a rechargeable
Lithium-polymer battery. It can be charged using the included USB cable cord via
connection to a computer. Battery charging must be done by adults only.
For indoor, dry-location use only:
Do not use the product near any wet locations.
Take care not to spill food or any liquid on this product as it may become inoperable.
If the unit does get wet, unplug all cables. Allow to dry thoroughtly before reusing. Do
not attempt to dry with a hair dryer or other heat source. Do not reconnect the USB
port if wet or damaged.
Avoid prolonged exposure to extreme temperatures and direct sunlight:
Operate in places with temperatures ranging from 5 C and 38 C . Do not leave the
product in your car as the temperatures in a car can exceed the acceptable storage
temperature. Exposure to extreme temperatures can result in shortened battery life or
cause the product to temporarily stop working.
Handle with care:
To avoid injury, damage to this product or other property, avoid
dropping and never disassemble, crush, puncture, microwave, incinerate, insert foreign
objects or paint the product.
Cleaning:
Disconnect all cords before cleaning. Clean the product with a slightly damp
cloth (cold water). Do not use soap, detergent or other chemicals. Never submerge the
unit in water. Allow to dry thoroughly before reusing. Do not connect the USB cable if
wet or damaged.
Reparing or modifying Peppa’s Play & Learn Smart Watch:
Never attempt
to repair or modify the product. If the product has been in contact with liquids,
punctured or subjected to a severe impact or fall, immediately remove this product
from use.
OPERATING INSTRUCTIONS
