.
.
QV12
EXPO SRL Strada Antica di None, 14
10092 Beinasco Torino ( Italia )
P.IVA 08909180013 Rea 1009634
MANUFACTURER EEC DECLARATION OF CONFORMITY
Hereby declares that the products Are in compliance with the following directive
2006/42/CEE
With reference to harmonised standard
EN 60335 – 1
.
USER INSTRUCTIONS MANUAL
. GENERAL INFORMATIONS .
We thank you for choosing our product . We ask you to please read these instructions carefully and to store them in a suitable place for easily
consultation.
Observe all indicated warnings to ensure proper equipment operation.
The manufacturer declines all responsibility for malfunctions caused by a failure to observe directions. All packaging materials utilised are ecological and
recyclable. Please dispose properly of packaging.
MALTIMENTO
. DISPOSING OF USED EQUIPMENT .
In accordance with art.13 of Legislative Decree of 25 July 2005, n.151 “Implementing Directives 2002/95/CE, 2002/96/CE and 2003/108/CE, concerning
the reduction of the use of hazardous substances in electrical and electronic equipment, as well as waste disposal"
.
The cross-out wheeled bin on the product or packaging or in the manual means that at the product end of life, it must be taken for separate collection.
Differentiated refuse collection of this product at the end of life is organised and managed by the manufacturer. The user desiring to rid him/herself of
this equipment must contact the manufacturer and follow the system arranged for separate collection at the end of life.
Adequate differentiated refuse collection in having the product recycled, treated and disposed of ecologically helps avoid possible negative effects on the
environment and health and supports the recycling of materials of which the equipment is made. Unlawful disposal of this product by the user will entail
fines foreseen by the current regulations.
. TECHNICAL INFORMATIONS .
To ensure maximised functioning, the equipment should be arranged in a well-aerated area without excessive moisture which is far from heat
sources, avoiding exposure to direct sunlight and keeping equipment clean from dust or other sediments.
Any damage or defects caused by failure to respect these norms are not covered by the guarantee and are not in any way the responsibility of the
manufacturer. It is also recommended to place the machine in order to enable the use when lighting conditions are “NORMAL” (quantified in 200 LUX)
E.D. 2006/42/EEC
ERTENZE
. SAFETY WARNINGS .
ELECTRIC SYSTEM
Fist of all check that the voltage supply corresponds to the one shown on the product data plate located on the back of the product .
A tolerance of +/- 6 % is allowed. It is very important to check the voltage level also during equipment operation, keeping in mind that
voltage lower
than the allowed tolerance can cause serious damage to the system
. Damage caused by a failure to observe the information in this paragraph is not
covered in any way by the guarantee.
Insert the supplied regulatory plug in a mono phase socket equipped with earthing. This socket must be permanently accessible to allow for equipment
disconnection at any time.
Installation earthing is not only a safety standard but is also obligatory by law. The manufacturer declines all
responsibility whenever this accident prevention standard is not respected.
Do not insert more than one plug at the same time in the same outlet using multiple outlets.
Do not spray any liquids or flammable gas directly inside or outside the cellar when the plug is inserted in the outlet.
OTHER SAFETY INFORMATION
The machine was designed and manufactured with reference to standards and were taken where possible all available security precautions, but still
hypothetical residual risk:
•
Beware of protruding corners and edges, that can cause cuts
•
The on and off all the moving parts is automatic. All moving parts are protected and in areas difficult to reach, it is recommended to disconnect power
before performing maintenance and clearing All moving parts are protected and in areas difficult to reach, it is recommended to disconnect
power before performing maintenance and clearing
•
Vacation time: If the appliance will not be used for several months, remove all items and turn off the appliance
.
•
before proceeding with cleaning and maintenance is recommended to disconnected the appliance and wait a few minutes
(In compliance with E.D. 2006/42/EEC)
