background image

 

QSG-THLK_Series-Rev2004 
Copyright © KBC Networks Ltd. 2020 

 

www.kbcnetworks.com 

 

 

ThruLink Quick Start Guide 

 
 

Introduction 

 

Welcome to KBC Networks’ Quick

 Start Guide for 

ThruLink. This document has been designed to 
provide a step-by-step guide to setting up a 
ThruLink server, client and linking them together. 
For more detailed information, please see the 
Downloads section below. 
 
The KBC ThruLink is an industrial hardware VPN that allows secure communications to be established 
over any standard public or private IP network infrastructure. ThruLink performs behind Firewalls, 
NAT and through almost any type of network configuration while offering advanced encrypted 
communication for all IP protocols regardless of the type of traffic. When deployed, ThruLink provides 
an advanced secure and encrypted private network that will not affect TTL, UPnP, VLAN information, 
broadcast, multicast or any other traffic. ThruLink can also be provided with an integrated 3G/4G 
modem that supports all primary network providers. 
 

Features 

 

Multiple hardware encryption engines ranging in complexity from 128 to 256bit

 

 

Encryption throughput models: SC (Standard Capacity): 15Mbps, SP (Standard Capacity 
Plus): 30Mbps, HC (High Capacity): 100Mbps, HP (High capacity Plus): 200Mbps

 

 

Optimized for stability, reduced latency of large packet streams over Public networks.

 

 

Automatically switch between GSM and LTE networks for best performance.

 

 

Supports MESH topology 

 no central server required.

 

 

Hardened against DOS and known common network attacks. 

 

Level 2 and Level 3 capable device. 

 

Auto re-syncing/authentication after a network failure, enabling a self-healing 
Encryption tunnel network. 

 

Support Multiple failover paths

 

 

Multiple networks can flow separately or combined over the same encryption tunnel.

 

 

Simplified installation.

 

 

Easy-to-use graphical user interface.

 

 

Can be installed within an existing network infrastructure. 

 

Downloads 

 
Full specifications, features and additional support information can be found on the relevant product 
page within the KBC Networks site: 

www.kbcnetworks.com

. 

 

 

 

Summary of Contents for ThruLink













Reviews: