KaVo KEY Laser 3+ 1343 Instructions For Use Manual Download | Manualshive

Page: 35 / 80

background image

▶ Press the handpiece axially all the way onto the laser hose coupling until it per‐

ceptibly locks in place.

▶ Before treatment, set the spray and run a user test.

See also: 4.17 Spray regulation, Page 55

See also: 4.8 User test with handpiece 2060, Page 40

4.3.3

Undo the connection

Note
Make sure that no water penetrates into the handpiece since this can distort the

detection and feedback.

Note
Make sure that the KEY Laser 3+ / III upgraded is switched to stand by.

Instructions for use KEY Laser 3+ 1343 KEY Laser III 1243 upgraded
4 Operation | 4.3 Laser hose and handpieces

33/76

«
...
33
34
35
36
37
...
»

Summary of Contents for KEY Laser 3+ 1343

















































































Reviews:

No comments

Related manuals for KEY Laser 3+ 1343

Brand: ABB Pages: 14

Brand: UnionSpecial Pages: 56

Brand: Olympus Pages: 86

Brand: GBC Pages: 8

Brand: KAPSCH Pages: 57

Brand: Keithley Pages: 149

Brand: Hanil Pages: 60

Brand: K&K Pages: 8

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Steri-Vac GS Series

Brand: 3M Pages: 52

Brand: Datavideo Pages: 28

Brand: NCR Pages: 20

Brand: DARAY Pages: 32

Body Armor Night Splint

Brand: Darco Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands