KaVo INTRAcompact contra-angle 2068 LHC Instructions For Use Manual Download Page 25 | Manualshive

Page: 25 / 64

background image

CAUTION

Connect to the drive motor.

Contra-angle handpiece blocked.

▶ Only start the contra-angle handpiece when the chuck is closed.

CAUTION

Removing and attaching the contra-angle handpiece while the drive motor

is rotating.

Damage to the drive.

▶ Never attach or remove the contra-angle handpiece while the drive

motor is rotating!

Operation

23

«
...
23
24
25
26
27
...
»

Summary of Contents for INTRAcompact contra-angle 2068 LHC

































































Reviews:

No comments

Related manuals for INTRAcompact contra-angle 2068 LHC

ACS880-01 Series

Brand: ABB Pages: 238

Brand: Navman Pages: 17

Brand: DARAY Pages: 24

Brand: Jafar Pages: 9

Brand: DARAY Pages: 28

Brand: MacDon Pages: 88

Brand: Jiffy Pages: 15

Litmann Quality 3100

Brand: 3M Pages: 2

Brand: JB Systems Pages: 12

Brand: Paia Pages: 11

Brand: CAB Pages: 39

Brand: CAB Pages: 27

Brand: Campbell Pages: 2

Brand: Gatekeeper Pages: 8

Bure Rise & Go DB 56-309

Brand: Gate Pages: 8

Brand: Macht Dental Pages: 8

Brand: RAPID REBOOT Pages: 18

Brand: MacDon Pages: 170

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands