manualshive.com logo in svg

Kaval LNKF800-A1, Instructions Manual For Installation, Operation And Maintenance

Share
Download
Kaval LNKF800-A1 Instructions Manual For Installation, Operation And Maintenance Download Page 7

 

LinkNet™  LNKF800 RF MODULES  

!

  USER MANUAL 

DCM000000014

 

 

 

Printed:  01.10.19,15:50 

 

Revision Date:10/19/01 

   7

 

 
 

 

Software Set-up 

The LNKF800 module is shipped with the following factory set options: 

OPTION 

RANGE OF VALUES  DEFAULT VALUE 

Frequency 

See Model Chart 

Order Specific 

Receive Threshold

 

–110 to -50 dB 

-89 dB 

Receive Hysteresis 

1 to 10 dB 

2.5 dB 

Time Out 

0 to 600 Seconds, or none 

300 Seconds 

Module Enabled 

On / Off 

On 

Transmit Power Level 

20 to 38 dBm 

Order Specific 

Default values may be changed when an order is placed.  Check your order 
confirmation (shipped with modules) for customized values. 

  

Configuration 

In line with the versatility of the LinkNet

TM

 Platform, it is possible to re-configure the 

LNKF800 module in the field, either with a 

Personal Computer (PC)

 or via the 

optional 

Control Module

. To use a 

PC

 it is necessary to have a 

Kaval 

CAB000000057 Control Cable

 to connect between the appropriate Module's DB15 

connector on the back of the Card-Cage and the standard DB9 RS232 Connector on 
the PC. On the PC a terminal emulation program such as 

HyperTerminal

 is used to 

communicate to the LinkNet Module. The settings are 9600 baud, 8 bits, no parity, 
and 1 stop bit. Commands are one or two words followed by pressing 

Return

. 

Commands may be given in upper or lower-case. Available commands are... 

ACCESS USER

: 

Required as a simple password to gain access to customer 
settable parameters and diagnostics; This will time-out after 10 
minutes, and may have to be re-typed.

 

HELP or  ?

: 

Displays a list of Available Commands. 

LIST

: 

Displays Current Settings and Status Faults, Etc. 

VER

: 

Display the current Version of Software. 

ENABLE 1 or 0

: 

Enables or Disables the Module. 

TXFREQ #########

: 

Displays or Sets the current Transmit Frequency (in Hertz). 

RXFREQ #########

: 

Displays or Sets the current Receive Frequency (in Hertz). 

TXPOWER ###

: 

Displays or Sets the Transmit Power Level (in tenths of a dBm). 

RXTHRESH -####

: 

Displays or Sets the Receive Threshold Level (in tenths of a dBm). 

RXHYSTER ##

: 

Displays or Sets the Receive Hysteresis (in tenths of a dB). 

TIMEOUT ####

: 

Displays or Sets the Timeout-Timer value (in Seconds). 

TESTOSC 1 or 0

: 

Enables or Disables the Test Oscillator. 

 

Please consult Kaval Wireless Technologies for further support.

Operation 

 

Summary of Contents for LNKF800-A1












Reviews:

No comments

Brands by name

Popular brands

Load more brands