manualshive.com logo in svg

Kathrein MobiSet 4 digital CAP 900, Installation And Operating Manual

Share
Download
Kathrein MobiSet 4 digital CAP 900 Installation And Operating Manual Download Page 2

2

CONTENTS

CONTENTS

 ...............................................................................................................................   2

FOREIGN LANGUAGE INSTALLATION MANUAL / DISPOSAL

 ....................................................   3

MOBISET 4 CAP 900 COMPONENTS / SCOPE OF DELIVERY 

 ....................................................   4

PROPER USE

 ...........................................................................................................................  5

SAFETY INSTRUCTIONS - IMPORTANT NOTES

 .........................................................................   6

INSTALLATION AND CONNECTION

 ...........................................................................................   9

INSTALLATION OF CABLE GLAND AND MOUNTING PLATE

 ...........................................................  11

INSTALLATION OF TURNTABLE

 ..............................................................................................   13

INSTALLATION OF THE UFS 740SW RECEIVER 

 ........................................................................   16

LAYING CABLES AND CONNECTING THE TURNTABLE

 ...............................................................   18

CONNECTING TO THE UFS 740SW

 .........................................................................................   18

FUNCTIONAL INSTRUCTIONS FOR CONNECTION TO THE ON-BOARD POWER SUPPLY

 ..................  19

CONNECTION EXAMPLE FOR 12 V BATTERY CONNECTION

 .................................................   20

RECEPTION RANGE / FOOTPRINT

 ..........................................................................................  21

DISMANTLING FOR SERVICING

 ..............................................................................................   22

DISMANTLING

 ......................................................................................................................  22

ADDRESS OF THE SERVICE CENTRE

 ...................................................................................   22

MANUAL LOWERING TO PARK POSITION

 ..............................................................................  23

SAFETY INSTRUCTIONS

 .......................................................................................................   23

MANUAL LOWERING

 .............................................................................................................  24

TECHNICAL DATA

 ..................................................................................................................  25

SIKAFLEX

®

 291 DATA SHEET

 .................................................................................................   26

SIKAFLEX

®

291 TECHNICAL DATASHEET

 ...............................................................................   27

CAP 900 OPERATING MANUAL

 ...............................................................................................  28

IMPORTANT INFORMATION FOR CAP 900 BEFORE SETUP

 ....................................................   29

REMOTE CONTROL

 ..............................................................................................................   29

FIRST INSTALLATION

 .............................................................................................................   30

ALIGNMENT (SATELLITE SEARCH)

 ........................................................................................  33

MANUAL CORRECTION

 ........................................................................................................  34

CHANNEL (SATELLITE) SELECTION

 .......................................................................................   35

CHANNEL SELECTION FROM THE CHANNEL LIST

 ................................................................   35

CHANGE OF LOCATION / TIMER PROGRAMMING

 ..................................................................  36

TIMER PROGRAMMING

 ........................................................................................................  36

RESET/PARKING

 ....................................................................................................................   37

RESETTING THE MOTORISED ANTENNA

 ..............................................................................   37

PARKING THE TURNTABLE

 ...................................................................................................   38

SPECIAL MESSAGES FROM THE TURNTABLE

 .......................................................................   39

SYSTEM PROTECTION MESSAGES

 ......................................................................................   39

MESSAGES ARISING FROM SOFTWARE PROBLEMS

 ............................................................   41

FURTHER MESSAGES

 ..........................................................................................................   42

DECLARATION OF CONFORMITY

 ...........................................................................................   43

Summary of Contents for MobiSet 4 digital CAP 900













































Reviews:

No comments

Brands by name

Popular brands

Load more brands