background image

MARKING FACSIMILE

EXPLANATORY MARKING DIAGRAM

INSTRUCTION FOR USE AND CARE

This hardhat is in compliance with the terms of the American Standards F1163.

Before using your KASK hardhat, please read the following instruction carefully. It is essential 

to use this hardhat properly, as not following the correct procedures could compromise your 

safety. 

In case an accident occurs, resulting in injury or death and it is due to the incorrect use of 

this hardhat, the manufacturer and the retailer decline all responsibility. 

This hardhat has been designed, produced and approved so as to ensure optimal protection 

during equestrian activities. It should not be used for purposes other than those specified 

by the manufacturer. 

It is not certified or tested to protect users against the crushing forces that may be sustained 

by a horse or other large animal stepping onto the helmet or rolling onto the helmet of its 

user. 

WEARING THE HARDHAT

As a preventive measure, it is imperative to wear the hardhat during all equestrian activities. 

For adequate protection, this hardhat must be worn correctly and adjusted according to the 

size of your head; to ensure this, several sizes are available to riders. 

Fasten the strap by inserting one buckle in the other until you hear it snap in place (Fig. 2). 

Check that the buckle is locked by tugging on it. Adjust the length of the chin-strap to firmly 

secure the helmet on your head and avoid the risk of the hardhat being pulled off. Ensure 

that the chinstrap is properly adjusted and tightened. 

The rubber ring must be positioned at the end of the tape to prevent it dangling. 

To be worn correctly, the hardhat should not move either back and forth or sideways (Fig. 1).

To  remove  the  helmet  from  the  head,  open  the  chin-strap  by  sliding  the  female  buckle 

forward (Fig. 2).

Any modification to the proper wearing of the hardhat could compromise the safety of the 

rider.

RECOMMENDATIONS

Before and after each use, check the condition of the hardhat inside and outside, as well 

as the chin strap.

When you’re not using the hardhat, store it away from direct sunlight and do not expose it 

to temperatures below -20°C (-4°F) or above 50°C (122°F).

Never  attempt  to  repair  or  modify  the  hardhat.  Following  a  violent  impact,  even  if  the 

hardhat  shows  no  visible  damage,  it  must  be  replaced  because  the  shock-absorbing 

material may have exhausted its protective capacity and therefore be unable to serve its 

purpose in the event of further impact.

The  date  of  manufacturing  appears  inside  the  hardhat,  under  the  inner  padding.  The 

lifespan of this KASK hardhat depends on the care and maintenance it receives, as well as 

on the frequency of its use.

TAKE CARE

The protection offered by the helmet depends on the circumstances of the accident; the 

wearer of a protective helmet will not always prevent death or long-term disability.

SPECIAL CARE

Clean  with  neutral  soap  and  water  only.  Allow  to  air  dry.  Never  clean  with  solvents  or 

chemical detergents (paint thinner, acetone, trichloroethylene, etc.) because they can alter 

the characteristics and quality of the hardhat. In general, avoid contact with corrosive or 

aggressive substances.

WARRANTY

For service or claims under the warranty, please see your KASK dealer.

KASK  agrees  to  supply  the  dealer  free  of  charge  with  a  replacement  for  any  defective 

component required to repair the hardhat for a period of two years from the date of the 

purchase invoice.

The warranty does not apply to:

- non-compliance with the specified use and maintenance.

- repairs or modifications (involving the total or partial disassembly of the hardhat) made by 

  the user or a company not approved by KASK.

MARKINGS/LABELLING:

 

The information contained on the inside of the helmet, printed on the label under the 

padding, should not be removed for any reason (Fig.3).

EN

1

KASK spa

5

2

DOGMA

3

EQUESTRIAN HELMET

6

06.2014

4

ASTM F1163

7

14.0000.0001

1

MANUFACTURER

5

CERTIFICATION MARKING

2

MODEL NAME

3

MODEL DESIGNATION

6

06.2014

4

REFERENCE STANDARDS

7

14.0000.0001

FASTENING
ACCROCHAGE

RELEASE
DÉCROCHAGE

Fig.2

Fig.1

Fig.3

OK

NO

NO

Reviews: