background image

170 West 600 North

 

Shelbyville, IN  46176

 

800

-

458

-

9129

 

www.kascomfg.com

 

 

LIMITED WARRANTY

 

 

Kasco Mfg. Co., Inc. warrants all its products marketed under the 

Herd

” 

trademark against defects 

in material and workmanship for three (3) months after date of retail purchase, except those       
components not manufactured by Kasco, as those parts are warranted only to the extent of the   
original manufacturer

s warranty. Our obligation under this warranty is limited to making good at 

the factory any defective part or parts thereof, which shall within three (3) months after delivery of 
such broadcaster to the original purchaser, to be returned to us. 

 

 

Should any part manufactured by Kasco prove defective within three months from date of retail           
purchase, supposed defective part shall be returned freight paid to Kasco for consideration. If found 
to be defective by Kasco, credit will be issued through the proper channels, distributor and/or     
dealer.

 

 

Kasco will not assume liability for any labor costs, loss or damage caused by a defective part,        
consequential damages, or operational delays.

 

 

Altering or misuse of a part will void this warranty. Repairing a part without the expressed             
permission of Kasco voids this warranty. Use of any mounting kit not manufactured by or               
recommended by the factor will void all warranty. 

 

 
 

Kasco neither assumes nor authorizes any person to assume for Kasco any other obligations or      
liability in connection with the sale of its equipment

 

 

Kasco reserves the right to make improvements in design or changes in specifications at any time 
without incurring any obligations to owners of equipment previously sold.

 

 

 

Summary of Contents for Herd I-258








Reviews: