Karel IA 12 Technical Reference And User'S Manual Download Page 2

 TECHNICAL REFERENCE  AND USER’S GUIDE   

REV AAA

IA12 ISDN ADAPTOR

 

 

 

 

              

CAUTION

 

Since IA12 ISDN Adaptor is an electronic-based product, the requirements below should 

be fulfilled, in order to utilize it with desired performance:

 

 

 

 

 

 

 

 

The  adaptor  must  not  be  disassembled  by  unauthorized 

 

 

 

 

persons in any way.

  

 

 

 

 

 

 

 

 

The  cover  of  the  adaptor  cabinet  should  always  be  kept 

 

 

 

 

closed. 

  

 

 

 

 

Prior to hanging the adaptor on the wall, one should make 

 

 

 

 

sure screws are not defective.

  

 

 

 

 

Precautions  must  be  taken  in  order  to  prevent  any  harmful 

 

 

 

 

substances from leaking or spilling into the adaptor in any way.

 

 

 

 

         

 

Failure in fulfilling these requirements may result in vital hazards!

IA12  USER’S GUIDE - REVAAA  15/08/2003

KAREL reserves the right to make modifications in product features mentioned in this 

document for development and improvement purposes, without prior notice. Individual 

products may possess characteristics different from those mentioned in this document, 

according to their software and hardware versions.

I

Summary of Contents for IA 12













Reviews: