background image

CONTENTS

2

 620-622 •  9.800-187.0  •  Rev. 9/10

Model Number ______________________________

Serial Number ______________________________

Date of Purchase ___________________________
The model and serial numbers will be found on a decal attached 
to the pressure washer. You should record both serial number and 
date of purchase and keep in a safe place for future reference.

Introduction & Important Safety Information 

3-5

Component Identification 

6

Set Up Procedures 

7

Operating Instructions 

7

Steam Combination 

7

Shutdown Procedures 

7

General Washing Techniques 

8

How to Use the Detergent Injector 

9

Preventative Maintenance and  Service 

10

Maintenance and Service 

11-12

Preventative Maintenance Schedule 

13

Troubleshooting 

14-17

Exploded Views 

18-19

Exploded View, Parts List 

20-21

Float Tank Exploded View & Parts List 

22

Hose and Spray Gun Assembly 

23

Pump Assembly, Exploded View and Parts List  

24-25

Control Panel, Exploded View and Parts List (1.575-620.0,-621.0)  26-27

Control Panel, Exploded View and Parts List (1.575-622.0) 

28-29

Steam Pump Exploded View & Parts List 

30

Burner Specifications 

31

KT.1 Series Pump Exploded View and Parts List 

32-33

VRT 3 Exploded View and Parts List 

34

PA8 5-3026 Unloader Exploded View and Parts List 

35-36

Warranty 

Summary of Contents for SSE-503007A







































Reviews: