Kärcher SC 3 Deluxe EasyFix Premium, Instructions Manual

Page: 12 / 16

The flash pulse for the set water hardness is indicat-
ed.
7. Repeat the process as necessary until the desired
water hardness level has been achieved.
Note
When the steam volume is pressed, the flash pulse for
the water hardness level is not indicated.
8. Press and hold the ON/OFF button for 4 seconds to
save the setting for the water hardness level. The
decalcification cartridge indicator light lights up.
Care of accessories
(Accessories - depending on scope of delivery)
Note
The micro fibre cloths are not suitable for dryer.
Note
When washing the cloths, observe the instructions on
the washing tag. Do not use any liquid softeners as this
will affect the ability of the cloths to pick up dirt.
1. Wash the floor cleaning cloths and covers at a max.
temperature of 60 °C in the washing machine.
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
WARNING
Risk of electric shock and burns
Trying to eliminate faults while the appliance is connect-
ed to the mains or has not yet cooled down is always
dangerous.
Remove the mains plug.
Allow the appliance to cool down.
The LED strip flashes red
The dry-run protection for the pump is activated.
1. Switch the device off and back on again.
2. Make sure that the decalcification cartridge has
been inserted correctly and there is sufficient water
in the reservoir.
No water in the water reservoir.
1. Top up the water reservoir, see chapter Topping up
the water .
The steam lever cannot be pressed
The steam lever is locked with the child lock.
Move the child lock forward.
The steam lever is released.
No / little steam although there is water in the reser-
voir
The decalcification cartridge has not been inserted or
has been inserted incorrectly.
Insert the decalcification cartridge or insert it cor-
rectly.
The decalcification cartridge has been removed while
topping up the water.
Leave the decalcification cartridge in the device
when topping up.
New decalcification cartridge has been inserted.
Press and hold the steam lever continuously.
The full steam output is reached after approximately
30 seconds.
Red “Replace decalcification cartridge” indicator
light lights up / flashes
The run time of the decalcification cartridge ends early.
Insert the new decalcification cartridge and reset the
maintenance indicator, see chapter Replacing the
decalcification cartridge .
The maintenance indicator was not reset after replace-
ment of the decalcification cartridge.
Press and hold the Maximum steam volume and
Reduced steam volume buttons at the same time
until the “Replace decalcification cartridge” indicator
light goes out after inserting the decalcification car-
tridge, see chapter Replacing the decalcification
cartridge .
The LED strip is in constantly red and no steam al-
though there is water in the reservoir
Run time for the decalcification cartridge has expired
Insert the new decalcification cartridge and reset the
maintenance indicator, see chapter Replacing the
decalcification cartridge .
The maintenance indicator is not reset after replace-
ment of the decalcification cartridge.
Press and hold the Maximum steam volume and
Reduced steam volume buttons at the same time
until the indicator light of "Replace decalcification
cartridge" goes out after inserting the decalcification
cartridge, see chapter Replacing the decalcification
cartridge .
Technical data
Subject to technical modifications.
SC 3 De-
luxe
EasyFix
Premi-
um
Electrical connection
Voltage V 220 -
240
Phase ~
Frequency Hz 50 - 60
Protection class IPX4
Protection category I
Performance data
Heating capacity W
Maximum operating pres-
sure
MPa
Heating-up time Sec-
onds
Continuous steaming g/min
Maximum steam blast g/min
Filling quantity
Water reservoir l
Dimensions and weights
Weight (without accesso-
ries)
kg
Length mm
Width mm
Height mm
1
1900
0.35
30
40
100
1.0
3.3
361
250
282