![background image](http://html2.mh-extra.com/html/karcher/premium-power-control-k3/premium-power-control-k3_manual_3513031013.webp)
English
13
2. Hold the storage option in the end position and se-
cure it using a screw.
Illustration E
Mounting the storage option for spray lances
1. Push in the storage option for the spray lances into
the holder on the device.
2. Hold the storage option in the end position and se-
cure it using a screw.
Illustration F
Mounting the storage option for the high-
pressure hose / mains connection cable
Devices without a hose reel
1. Push in the storage option for the high-pressure
hose / mains connection cable into the holder on the
transport handle.
2. Hold the storage option in the end position and se-
cure it using a screw.
Illustration G
Mounting the high-pressure hose reel
Devices with a hose reel
1. Attach the holder for the hose reel.
2. Secure the holder using 2 screws.
Illustration H
3. Attach the hose reel.
The hose reel locks into place.
Illustration I
Installing the water connection coupling
1. Screw the water connection coupling onto the water
connection on the device.
Illustration J
Initial startup
1. Place the device on a flat and level surface.
2. Unwind the high-pressure hose and eliminate any
loops and twists.
Note
Devices with a hose reel During operation, the high-
pressure hose must be completely unwound from the
hose reel.
3. Connect the high-pressure hose to the device.
a Pull up the clamp on the coupling.
b Insert the high-pressure hose into the coupling.
c Press down the clamp on the coupling.
Illustration K
4. Connect the high-pressure hose to the high-pres-
sure gun.
a Squeeze the clamp.
b Pull out the clamp.
c Insert the high-pressure hose.
d Press the clamp in until it latches into place.
Illustration L
5. Check for a secure connection by pulling on the
high-pressure hose.
6. Plug the mains plug into a mains socket.
Water supply
For the connection values, see the type plate or chapter
Observe the water distribution company regulations.
ATTENTION
Damage through contaminated water
Contamination in the water can damage the pump and
the accessories.
KÄRCHER recommends using the KÄRCHER water fil-
ter for protection(special accessory, order number
4.730-059).
Connection to the water line
ATTENTION
Hose coupling with Aquastop on the water connec-
tion of the device
Damage to the pump
Never use a hose coupling with Aquastop on the water
connection of the device.
You can use an Aquastop coupling on the tap.
1. Plug the garden hose onto the water connection
coupling.
2. Connect the garden hose to the water line.
Illustration M
3. Open the water tap fully.
Operation
ATTENTION
Pump running dry
Damage to the device
If pressure does not build up in the device after 2 min-
utes then switch the device off and proceed according
to the instructions in chapter Troubleshooting guide.
High-pressure operation
ATTENTION
Damage to painted or sensitive surfaces
Surfaces can be damaged when the jet is too close to
the surface or an unsuitable spray lance is used.
Maintain a minimum spray distance of 30 cm when
cleaning painted surfaces.
Do not clean car tyres, paint or sensitive surfaces such
as wood with the dirt blaster.
1. Insert a spray lance into the high-pressure gun and
lock it by turning it 90°.
Illustration N
2. Switch the device on ("I/ON").
3. Unlock the lever of the high-pressure gun.
4. Press the lever of the high-pressure gun.
The device switches on.
Operation with detergent
DANGER
Failure to adhere to the safety data sheet
Incorrect handling of the detergent can seriously dam-
age your health
Observe the safety data sheet of the detergent manu-
facturer, in particular the instructions on personal pro-
tective equipment.
Note
KÄRCHER detergents ensure fault-free operation. Ask
us for a consultation, request our catalogue or our de-
tergent information sheets.
Note
Detergent can only be mixed into the jet at low pressure.
1. Pull the desired length of the detergent suction hose
out of the casing.
Illustration O
2. Hang the detergent suction hose in a container with
detergent solution.
3. Use the Vario Power spray lance.
4. Turn the spray lance all the way into the "SOFT" po-
sition.
The detergent solution is mixed with the water jet
during operation.
Summary of Contents for Premium Power Control K3
