background image

12

English

4. Remove the fine filter using the suc-

tion hose connection or suitable pliers.

5. Clean the valve opener and the fine

filter under running water.

6. Insert the fine filter and the valve

opener. Make sure that the pin of the
valve opener points upwards.

Troubleshooting guide

DANGER

Contact with live parts

Injury due to electric shock
Before carrying out any work on the 
device, switch it off and disconnect it 
from the charger.
Have repair work and work on electri-
cal components carried out only by au-
thorized Customer Service personnel.
Malfunctions often have simple causes 
that you can remedy yourself using the 
following overview. When in doubt, or 
in the case of malfunctions not men-
tioned here, please contact your autho-
rized Customer Service.

Device is not running

The charging state of the battery is too low.
1. Check the charging state of the bat-

tery, charge the battery if necessary.

The motor is overloaded, the motor cir-
cuit breaker has tripped.
1. Switch off the device.
2. Switch on the device and put it into

operation.

The ambient temperature is outside 
the permissible range (see chapter  
Technical data), 
the motor circuit 
breaker has tripped.
1. Switch off the device.
2. Allow the device to cool down / heat up.
3. Switch on the device and put it into

operation.
If the fault occurs several times,
have the device checked by Cus-
tomer Service.

The device does not reach required 
pressure

1. Ensure that there is sufficient water

in the reservoir or water container.

2. Clean the valve opener and the fine

filter (see chapter  Cleaning the
valve opener / fine filter).

3. Make sure that the valve opener is in-

serted with the pin pointing upwards.

Strong pressure fluctuations

1. To clean the nozzle: Remove the dirt

from the nozzle bore with a needle
and rinse with water from the front.

2. Ensure that there is sufficient water

in the reservoir or in the water con-
tainer.

Device leaking

1. A slight leakage in the device is due

to technical reasons. In case of se-
vere leakage, contact an authorized
Customer Service center.

Warranty

The warranty conditions issued by our 
relevant sales company apply in all 
countries. We shall remedy possible 
malfunctions on your appliance within 
the warranty period free of cost, provid-
ed that a material or manufacturing 
flaw is the cause. In a warranty case, 
please contact your dealer (with the 
purchase receipt) or the next autho-
rized customer service site.
(See overleaf for the address)

Summary of Contents for OC 3













Reviews: