background image

7

SHUTTING DOWN & CLEAN-UP

Step 1

Remove 

detergent suction tube
from container and insert
into one gallon of fresh
water. Siphon water at low
pressure for one minute.

Step 2  

Turn off the
engine.

Step 3  

Turn off the water
source.

Step 4  

Press trigger to
release water 
pressure.

Step 5

Disconnect the

garden hose from the
water inlet on the unit.

Step 6

Disconnect the high pressure hose from the

high pressure outlet and engage the gun safety lock.

WINTERIZING AND LONG-TERM STORAGE       

1. Disconnect all water connections.
2. Start the machine for a few seconds, until

the water which had remained in the pump
exits. Turn off immediately.

3. Drain the gas and oil from the engine.
4. Do not allow high pressure hose to

become kinked.

5. Store the machine and accessories in 

a room which does not reach freezing
temperatures. The machine should not be
placed near an open flame i.e. furnace,
hot water heater etc.

Caution: Failure to follow the above direc-
tions will result in damage to the pump
assembly and accessories.

TAKING A BREAK... five minutes or more

Step 1

Turn off the

engine.

Step 3

Engage gun

safety lock.

Step 2

Press trigger to

release water pressure.

Summary of Contents for K 1800 AB













Reviews: