background image

 

English

 3

Please read and comply 
with these instructions prior 

to the initial operation of your appli-
ance. Retain these operating instruc-
tions for future reference or for 
subsequent possessors.

Environmental protection

3

Safety instructions

4

Proper use

5

Function

5

Control elements

5

Start up

6

Operation

7

Shutting down

9

Transport

9

Maintenance and care

9

Troubleshooting

10

Technical specifications

12

Warranty

13

WARNING 

When using this product basic precau-
tions should always be followed, in-
cluding the following:

„

Read all the instructions before us-
ing the product.

„

To reduce the risk of injury, close 
supervision is necessary when a 
product is used near children.

„

Know how to stop the product and 
bleed pressures quickly. Be thor-
oughly familiar with the controls.

„

Stay alert – watch what you are do-
ing.

„

Do not operate the product when fa-
tigued or under the influence of al-
cohol or drugs.

„

Keep operating area clear of all per-
sons.

„

Do not overreach or stand on unsta-
ble support. Keep good footing and 
balance at all times.

„

Follow the maintenance instructions 
specified in the manual.

„

Examine mains cable before using 
and do not use the machine if the 
mains cable is damaged.

„

Do not abuse mains cable and do 
not yank on any cord to disconnect.

„

Keep mains cable away from heat 
and sharp edges.

„

Risk of Injection or Injury – Do Not 
Direct Discharge Stream At Per-
sons.

„

Risk Of Explosion – Do not spray 
flammable liquids.

CAUTION

„

Gun Kicks Back – Hold with both 
hands.

„

Cold surfaces – use only designed 
gripping areas of lance (wand or 
gun).

WARNING 

„

TO REDUCE THE RISK OF ELEC-
TROCUTION, KEEP ALL CON-
NECTIONS DRY AND OFF 
GROUND. DO NOT TOUCH PLUG 
WITH WET HANDS.

„

TO REDUCE THE RISK OF FIRE, 
ELECTRIC SHOCK OR INJURY:
INJECTION HAZARD: EQUIP-
MENT CAN CAUSE SERIOUS IN-
JURY IF THE SPRAY 
PENETRATES THE SKIN. DO 
NOT POINT THE GUN AT ANY-
ONE OR ANY PART OF THE 
BODY. IN CASE OF PENETRA-
TION SEEK MEDICAL AID IMME-
DIATELY.

„

THIS SYSTEM IS CAPABLE FOR 
PRODUCING 1000 kPa. TO AVOID 
RUPTURE AND INJURY, DO NOT 
OPERATE THIS APPLIANCE 
WITH COMPONENTS RATED 
LESS THAN 1000 kPa WORKING 
PRESSURE (INCLUDING BUT 
NOT LIMITED TO SPRAY GUNS, 
HOSE AND HOSE CONNEC-
TIONS).

„

BEFORE SERVICING, CLEAN-
ING, OR REMOVAL OF ANY 
PART, SHUT OFF POWER AND 
RELIEVE PRESSURE.

„

HIGH PRESSURE. KEEP CLEAR 
OF NOZZLE.

„

CLOSE COVER BEFORE OPER-
ATING THE MACHINE.

„

THIS APPLIANCE IS INTENDED 
FOR COMMERCIAL USE.

„

DO NOT SPRAY ENERGIZED 
ELECTRICAL APPARATUS AND 
WIRING.

SAVE THESE INSTRUCTIONS!

This product must be grounded. In the 
event of an electrical short circuit, 
grounding reduces the risk of electrick 
shock by providing an escape wire for 
the electric current. This product is 
equipped with a cord having a ground-
ing wire with an appropriate grounding 
plug. The plug must be plugged into an 
outlet that is properly installed and 
grounded in accordance with all local 
codes and ordinances.

WARNING 

Improper installation of the grounding 
plug is able to result in a risk of electric 
shock. When repair or replacement of 
the cord or plug is required, do not con-
nect the grounding wire to either flat 
blade terminal. The wire with insulation 
having an outer surface that is green 
with or without yellow stripes is the 
grounding wire. Check with a qualified 
electrician or serviceman when the 
grounding instructions are not com-
pletely understood, or when in doubt as 
or whether the product is properly 
grounded. Do not modify the plug pro-
vided; if it does not fit the outlet, have a 
proper outlet installed by a qualified 
electrician.
This product is for use on a nominal 
120-V circuit and has a grounding plug 
similar to the plug illustrated in sketch 
A. Only connect the product to an outlet 
having the same configuration as the 
plug. Do not use an Adapter with this 
product.

1 Grounded outlet
2 Grounded outlet box
3 Grounded pin

Contents

Environmental protection

The packaging material can 
be recycled. Please do not 
place the packaging into the 
ordinary refuse for disposal, 
but arrange for the proper 
recycling.

Old appliances contain 
valuable materials that can 
be recycled. Please ar-
range for the proper recy-
cling of old appliances. 
Batteries, oil, and similar 
substances must not enter 
the environment. Please 
dispose of your old appli-
ances using appropriate 
collection systems.

IMPORTANT SAFETY IN-

STRUCTIONS

GROUNDING INSTRUCTIONS

Summary of Contents for IB 7/40 Classic









































Reviews: