![background image](http://html.mh-extra.com/html/karcher/hds-8-18-4-c/hds-8-18-4-c_manual_655230019.webp)
– 4
Note:
Ensure that the solenoid valve cable on the res-
ervoir of the system care is not pinched.
–
For connection values, see technical data and type
plate.
–
The electrical connections must be done by an
electrician according to IEC 60364-1.
DANGER
Risk of injury on account of electric shock!
–
Unsuitable electrical extension cables can be haz-
ardous. Only use electrical extension cables out-
doors which have been approved and labelled for
this purpose and have an adequate cable cross-
section.
–
Always unwind extension lines completely.
–
The plug and coupling of the extension cable used
must be watertight.
ATTENTION
The highest allowed net impedance at the electrical
connection point (refer to technical data) is not to be ex-
ceeded. In case of confusion regarding the power im-
pedance present on your connection, please contact
your utilities provider.
DANGER
Danger of explosion! Do not spray flammable liquids.
DANGER
Risk of injury! Never use the appliance without the spray
lance attached. Check and ensure proper fitting of the
spray lance prior to each use. The screw connection of
the spray lance must be finger-tight.
DANGER
Risk of injury! Hold the hand spray gun and the spray
pipe firmly with both hands.
DANGER
Risk of injury! The trigger and safety lever may not be
locked during the operation.
DANGER
Risk of injury! Contact Customer Service if the safety le-
ver is damaged.
ATTENTION
Risk of damage! Never operate device with an empty
fuel tank. The fuel pump will otherwise be destroyed.
To open the trigger gun: Actuate the safety lever
and trigger.
To close the hand spray gun: Release the safety le-
ver and trigger.
DANGER
Risk of injury! Switch the appliance off prior to replacing
nozzle and activate hand spray gun until device is pres-
sureless.
Secure the trigger gun. To do so, push the safety
catch towards the front.
Replacing the nozzle.
Set appliance switch to desired operating mode.
Indicator lamp for operational readiness lights up.
The device starts briefly and turns off, as soon as the
working pressure is reached.
Note:
If the control lamp "rotation direction" lights up,
please switch the appliance off immediately and fix the
error, see "Help with malfunctions".
Release the trigger gun. To do so, push the safety
catch towards the back.
When activating the hand spray gun the device switch-
es back on.
Note:
If no water comes out of the high pressure nozzle,
vent pump. Refer to "Help with malfunctions - appliance
is not building up pressure".
Set device switch to desired temperature.
30 °C to 98 °C
–
Clean with hot water.
100 °C to 150 °C
–
Clean using steam.
In steam operation (> 100°C), use the steam noz-
zle available as an accessory (see “Steam opera-
tion”).
Turn the regulation spindle in a clockwise direction:
Increase working pressure (MAX).
Turn the regulation spindle in an anti-clockwise di-
rection: Reduce working pressure (MIN).
–
For considerate treatment of the environment use
detergent economically.
–
The detergent must be suitable for the surface to
be cleaned.
With support of the detergent dose valve set deter-
gent concentration as determined by the manufac-
turer.
Note:
Recommended values at the control panel at
maximum working pressure.
Note:
If detergent is be suctioned from an external con-
tainer, route the detergent suction hose through the re-
cess to the outside.
Set pressure/temperature and detergent concen-
tration according to the surface to be cleaned.
Note:
To prevent damage due to too much pressure, al-
ways position high pressure ray first from a greater dis-
tance towards object to be cleaned.
–
Loosen the dirt:
Spray detergent economically and let it work for
1...5 minutes but do not let it dry up.
–
Remove the dirt:
Spray off loosened dirt with the high pressure jet.
Removal of light contaminations and clear rinse, i.e.:
Gardening tools, terrace, tools, etc.
Set operating pressure according to need.
The appliance works in the most economical tempera-
ture range (max. 60 °C).
Power connection
Operation
Opening/closing the trigger gun
Replace the nozzle
Turning on the Appliance
Adjust cleaning temperature
Set working pressure and flow rate
Pressure/quantity regulation of the pump unit
Operation with detergent
Cleaning
Recommended cleaning method
Operating with cold water
Eco level
19
EN
Summary of Contents for HDS 8/18-4 C
