background image

17

Operations

Assembly Instructions

STEP 1:

 Attach a 5/8" garden hose 

to inlet connector. Minimum flow 
should be 5 gpm.

STEP 4:

 Check oil level on sight 

glass on backside of pump. Oil 
should be visible one-half way up 
sight glass (10-40W non-foaming). 
The oil level can also be checked 
by using the dipstick on the top of 
the pump.

STEP 2:

 Attach high pressure hose 

to discharge nipple using quick 
coupler. Lock coupler securely into 
place by pulling back coupler collar 
and inserting it onto discharge 
nipple, then pushing collar forward 
to lock in place.

NOTE: If using detergent injector, 
attach detergent injector to 
discharge nipple using quick 
coupler. Attach high pressure 
hose to other end of detergent 
injector.

STEP 5:

 Fill gasoline tank and 

check engine oil.

Fill diesel tank with diesel fuel.

CAUTION: Do not confuse diesel 
fuel and gasoline when filling 
tanks. Keep proper fuel in proper 
tanks.

NOTE: Diesel Fuel Shut-off must 
be in the ON position prior to 
turning on burner.

STEP 3:

 Attach wand to spray gun 

using teflon tape on threads to 
prevent leakage. Attach swivel 
connector on discharge hose to 
spray gun using teflon tape on 
threads. Attach swivel connector on 
high pressure hose to spray gun 
using teflon tape on threads. 
Engage safety latch to prevent from 
triggering gun.

STEP 6:

 On electric start models, 

you will need to install a battery 
making sure that the red cable is 
attached to the positive terminal. 
Use  a Group U1 garden tractor 
style type of battery rated for 300 
CCA (battery not included). 

NOTE: 

Battery is required for 

burner to operate.

CAUTION: These machines are 
intended to be protected from 
outside environments.

CAUTION: Risk of injury. Discon-
nect battery ground terminal 
before servicing.

Karcher HDS 3.5/40 GE MT Operator’s Manual  9.807-942.0 - B

Inlet 

Connector

High Pressure

Hose

Discharge

Nipple

Detergent 
Hose

Detergent 

Injector

(Option)

Dipstick

Gasoline

Tank

POS

NEG

Red

Black

Diesel Fuel

Tank

Safety 

Latch

Summary of Contents for HDS 3.5/40 GE MT

































Reviews: