background image

English

Operating Instructions HD 645 / HD 650 (SX) / HD 658 / HD 690 (SX)

18

Relief valve, pressure switch and safety 
valve are set and sealed in the factory.

Adjustments are made only by Customer 
Service.

Warranty

The warranty terms issued by our authorised 
marketing company are valid in every 
country. We remedy any fault in the cleaner 
free of charge within the warranty period 
providing the cause of the fault proves to be 
a material or manufacturing error.

The warranty only becomes operative 
when your dealer has completed the reply 
card accompanying the sale of the unit, has 
stamped and signed it and you have then 
sent the reply card to the marketing 
company in your country.

Should you wish to call upon the guarantee, 
please apply to your dealer or nearest 
authorised Customer Service centre taking 
along also the accessories and bill of sale.

Preparing the cleaner for 
use

Unpack the cleaner

– When unpacking the cleaner, check the 

contents of the packaging. If there has 
been any damage in transit inform the 
dealer.

– Do not dispose of the packaging with the 

household rubbish, hand it in at the 
appropriate collection point for recycling.

Check the oil level

Fig. 

1

 – 

3

„

Screw out the fastening screws on the 
left and right of the unit cover, remove 
unit cover.

„

Cut off the tip on the cover to the oil 
reservoir.

„

Check the oil level in the oil reservoir.

„

Fasten the unit cover.

Mount the accessories

Fig. 

4

 – 

9

„

Mount handle (screws and nuts 
supplied).

„

Engage the holder for handgun at the 
side of the handle.

„

Mount nozzle on the spray lance (see 
markings on the top of the setting ring).

„

Mount spray lance on the handgun.

„

Insert and engage the crank handle in 
the hose-reel axle.

„

Mount the high-pressure hose on the 
hose reel. Insert the high-pressure hose 
nipple through the opening in the hose-
reel hub and into the hose holder. Secure 
the high-pressure hose with the hook.

„

Check:

 It should not be possible for the 

hose nipple to be pulled out.

„

It is advisable to lay the high-pressure 
hose out in a straight line before reeling 
it up.

„

Wind the high-pressure hose up in even 
layers on the hose reel by turning the 
crank handle.

Summary of Contents for HD 645














Reviews: