background image

After operation with detergent

1. Flush the foam lance with clear water for approx. 30 

seconds.

Replacing the nozzle

DANGER

Risk of injury!

Switch the device off prior to replacing nozzle and do 

not activate hand spray gun until the device is pressure-

less.

1 Secure the high-pressure gun. To do so, push the 

safety lever towards the front.

2 Unscrew nozzle screws and remove the nozzle.

3 Put on a new nozzle.

4 Screw on the nozzle screws and tighten them by 

hand.

Interrupting operation

Note

When the device is shut down, the water pressure will 

be reduced, which can reduce the operating force of the 

high-pressure gun and improve the service life of the 

equipment.

1. Close the high-pressure gun, the device will inter-

rupt.

2. Push the safety lock forward to close the safety lock 

of the high-pressure gun.

3. Push the safety lock back to open the safety lock of 

the high-pressure gun. 

4. Open the high-pressure gun, the device will switch 

on again.

Finishing operation

1. Shut off the water supply.

2. Open the high-pressure gun.

3. Set the power switch to "1" and let the device run for 

5 to 10 seconds.

4. Set the power switch to "0" .

5. Close the high-pressure gun.

6. Unplug the power supply from the device with dry 

hands.

7. Remove water inlet.

8. Close the safety lever of the high-pressure gun and 

push the safety lock forward.

Transportation

CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during transporta-

tion.

1. Place the spray lance with the high-pressure gun on 

the hooks.

2. Wind the power cable around the cable hooks.

3. Without hose reel: Wind up the high-pressure hose 

and hang it over the hook. 

With hose reel: Wind the high-pressure hose onto 

the hose reel.

4. When transporting the device in vehicles, secure the 

device against shifting and tipping over.

5. For short distance transportation, pull the telescopic 

handle to drag the device.

Illustration G

6. When going up stairs, hold the additional handle 

and lift the device up.

Illustration H

Storage

CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during storage.

Store the device indoors only.

Frost protection

ATTENTION

Frost destroys the device if it is not completely 

drained of water.

Store the device in a frost-free location.

If frost-free storage is not possible:

1. Drain excess water.

2. Pump commonly available anti-freeze through the 

device.

3. Allow the device to run for a maximum of 1 minute 

until the pump and lines are empty.

Note

Use commonly available, Glycol-based vehicle anti-

freeze. Observe the handling instructions of the anti-

freeze manufacturer.

Care and service

DANGER

Inadvertently starting up the device

Risk of injury, electric shock

Switch off the device immediately and unplug the mains 

plug before performing work.

Note

Old oil may only be disposed of at designated collection 

points. Please dispose of any old oil at these locations. 

Polluting the environment with old oil is punishable by 

law.

Safety inspection/maintenance contract

You can agree on regular safety inspections or close a 

maintenance contract with your dealer. Please seek ad-

vice on this.

Maintenance intervals

Each time before use

1. Check the power cable for damage and have a dam-

aged cable replaced immediately by the authorised 

Customer Service or a qualified electrician.

2. Check the high-pressure hose for damage and re-

place a damaged high-pressure hose immediately.

3. Check the device for leaks. 3 drops of water per min-

ute are permissible. Contact Customer Service in 

the case of more serious leaks.

Weekly

1. Clean the water filter, see Chapter

 Cleaning the wa-

ter filter

.

Every 500 operating hours, at least once annually

Have the oil changed by Customer Service.

Maintenance work

Cleaning the water filter

ATTENTION

Damaged water filter in the water connection

Damage to the device through contaminated water

Check the water filter for damage before inserting it into 

the water connection.

1. Pull the water filter out.

2. Clean the water filter under running water.

English

12

Summary of Contents for HD 4/8 Classic



















Reviews: