background image

12

Please remove the spark plug cable to

prevent accidental ignition of the engine

before making any repair.

Engine will not start.

• No gasoline.

- Fill gas tank.

• Choke is not in correct position.

- Slide choke lever out to closed

position.

• Engine throttle is not in correct

position.

- Slide the throttle lever up about 1/3 of

the way toward the fast positon.

• Pressure built up in the high pressure

washer.

- Squeeze the trigger to release the

pressure.

For additional engine problems refer
to the engine owners manual.

Unit does not reach high pressure.

• Diameter of garden hose is too small.

- Replace with a 3/4 inch garden hose.

• Water supply is restricted.

- Check garden hose for kinks, leaks

and blockage.

• Not enough inlet water supply.

- Open water source full force.

• Water inlet filter is clogged.

- Remove filter and rinse out in warm

water.

• Black detergent nozzle is attached.

- Remove black detergent nozzle and

attach a high pressure nozzle.

Output pressure varies high and low.

• Not enough inlet water supply.

- Turn water on full force. Check garden

hose for kinks, leaks or blockage.

• Pump is sucking air.

- Check that hoses and fittings are air

tight. Turn off machine and purge
pump by squeezing trigger gun until a
steady flow of water emerges through
the nozzle.

• Water inlet filter is clogged.

- Remove filter and rinse out in warm

water.

• Spray nozzle is obstructed.

- Blow out or remove debris with a fine

needle.

• Calcified gun, hose or spray wand.

- Run distilled vinegar through

detergent suction tube.

No detergent.

• Detergent suction tube not properly

connected to the machine.

- Check connection.

• Detergent is too thick.

- Dilute detergent. For best results, use

Kärcher detergent.

• Detergent filter valve is at lowest

setting.

- Set detergent filter valve to a higher

setting.

• Filter on detergent suction tube is

clogged.

- Run warm water through filter to

remove debris.

• Damaged or clogged detergent

suction tube.

- Remove obstruction or replace

detergent suction tube.

• A high pressure nozzle is attached.

- Replace with black detergent nozzle.

• Spray nozzle is obstructed.

- Blow out or remove debris with fine

needle.

TROUBLESHOOTING

Summary of Contents for HD 2.6/26 P














Reviews: